NetApp FAS2600 Скачать руководство пользователя страница 135 | Manualshive

Страница: 135 / 786

background image

2. Gently pull the caching module straight out of the housing.

3. Move the caching module to the new controller module, and then align the edges of the caching module

with the socket housing and gently push it into the socket.

4. Verify that the caching module is seated squarely and completely in the socket.

If necessary, remove the caching module and reseat it into the socket.

5. Reseat and push the heatsink down to engage the locking button on the caching module housing.

6. Close the controller module cover, as needed.

Step 6: Install the controller

After you install the components from the old controller module into the new controller module, you must install
the new controller module into the system chassis and boot the operating system.

For HA pairs with two controller modules in the same chassis, the sequence in which you install the controller
module is especially important because it attempts to reboot as soon as you completely seat it in the chassis.

The system might update system firmware when it boots. Do not abort this process. The
procedure requires you to interrupt the boot process, which you can typically do at any time after
prompted to do so. However, if the system updates the system firmware when it boots, you must
wait until after the update is complete before interrupting the boot process.

Steps

1. If you are not already grounded, properly ground yourself.

2. If you have not already done so, replace the cover on the controller module.

3. Align the end of the controller module with the opening in the chassis, and then gently push the controller

module halfway into the system.

Do not completely insert the controller module in the chassis until instructed to do so.

4. Cable the management and console ports only, so that you can access the system to perform the tasks in

the following sections.

You will connect the rest of the cables to the controller module later in this procedure.

5. Complete the reinstallation of the controller module:

133

«
...
133
134
135
136
137
...
»

Содержание FAS2600



















































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для FAS2600

Soundgear Series

Бренд: JBL Страницы: 73

Sportsound SSR-300

Бренд: Daktronics Страницы: 6

Бренд: Panasonic Страницы: 24

Бренд: Panasonic Страницы: 24

Бренд: Panasonic Страницы: 28

Бренд: Panasonic Страницы: 32

Бренд: Panasonic Страницы: 20

Бренд: Mitsubishi Electric Страницы: 50

Бренд: jWIN Страницы: 16

Бренд: RCA Страницы: 13

Бренд: RCA Страницы: 20

Бренд: TriangleTube Страницы: 26

Бренд: Aiwa Страницы: 63

Бренд: Aiwa Страницы: 76

Бренд: Hyundai Страницы: 46

Бренд: Rane Страницы: 36

Бренд: Geneva Страницы: 6

Бренд: Teac Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды