NetApp FAS2600 Скачать руководство пользователя страница 589 | Manualshive

Страница: 589 / 786

background image

cluster_B::> metrocluster show
Cluster Configuration State Mode
-------------------- ------------------- ---------
Local: cluster_B configured switchover
Remote: cluster_A configured waiting-for-switchback

The switchback operation is complete when the clusters are in the

normal

state.:

cluster_B::> metrocluster show
Cluster Configuration State Mode
-------------------- ------------------- ---------
Local: cluster_B configured normal
Remote: cluster_A configured normal

If a switchback is taking a long time to finish, you can check on the status of in-progress baselines by using
the

metrocluster config-replication resync-status show

command.

6. Reestablish any SnapMirror or SnapVault configurations.

Step 6: Return the failed part to NetApp

Return the failed part to NetApp, as described in the RMA instructions shipped with the kit. See the

page for further information.

Hot-swap a caching module - AFF A700 and FAS9000

The NVMe SSD FlashCache modules (FlashCache or caching modules) are located in
the front of the NVRAM10 module in Slot 6 of FAS9000 systems only. Beginning with
ONTAP 9.4, you can hot-swap the caching module of the same capacity from the same or
different supported vendor.

Before you begin

Your storage system must meet certain criteria depending on your situation:

• It must have the appropriate operating system for the caching module you are installing.

• It must support the caching capacity.

• The replacement caching module must have the same capacity as the failed caching module, but can be

from a different supported vendor.

• All other components in the storage system must be functioning properly; if not, you must contact technical

support.

Steps

1. If you are not already grounded, properly ground yourself.

2. Locate the failed caching module, in slot 6, by the lit amber Attention LED on the front of the caching

module.

587

«
...
587
588
589
590
591
...
»

Содержание FAS2600



















































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для FAS2600

Бренд: auna multimedia Страницы: 124

Бренд: NAIM Страницы: 31

MR Confon Starter f MKII+

Бренд: Cambridge Research Systems Страницы: 34

Бренд: JVC Страницы: 51

Бренд: JVC Страницы: 37

Бренд: JVC Страницы: 27

Бренд: JVC Страницы: 24

Бренд: JVC Страницы: 2

Бренд: JVC Страницы: 72

Бренд: JVC Страницы: 58

Бренд: JVC Страницы: 34

Бренд: JVC Страницы: 28

Бренд: JVC Страницы: 70

Бренд: JVC Страницы: 88

Бренд: JVC Страницы: 41

Бренд: JVC Страницы: 103

Бренд: JVC Страницы: 61

Бренд: JVC Страницы: 29

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды