NetApp FAS2600 Скачать руководство пользователя страница 761

Страница: 761 / 786

Cam handle release button

Cam handle

Do not completely insert the controller module in the chassis until instructed to do so.

4. Cable the management and console ports only, so that you can access the system to perform the tasks in

the following sections.

You will connect the rest of the cables to the controller module later in this procedure.

5. Complete the reinstallation of the controller module:

a. If you have not already done so, reinstall the cable management device.

b. Firmly push the controller module into the chassis until it meets the midplane and is fully seated.

The locking latches rise when the controller module is fully seated.

Do not use excessive force when sliding the controller module into the chassis to avoid
damaging the connectors.

The controller module begins to boot as soon as it is fully seated in the chassis. Be prepared to
interrupt the boot process.

c. Rotate the locking latches upward, tilting them so that they clear the locking pins, and then lower them

into the locked position.

d. Interrupt the boot process by pressing

Ctrl-C

when you see Press Ctrl-C for Boot Menu.

e. Select the option to boot to Maintenance mode from the displayed menu.

Step 5: Run system-level diagnostics

After installing a new DIMM, you should run diagnostics.

Your system must be at the LOADER prompt to start System Level Diagnostics.

All commands in the diagnostic procedures are issued from the node where the component is being replaced.

1. If the node to be serviced is not at the LOADER prompt, perform the following steps:

a. Select the Maintenance mode option from the displayed menu.

b. After the node boots to Maintenance mode, halt the node:

halt

After you issue the command, you should wait until the system stops at the LOADER prompt.

During the boot process, you can safely respond

to prompts.

▪

If a prompt appears warning that when entering Maintenance mode in an HA configuration, you
must ensure that the healthy node remains down.

2. At the LOADER prompt, access the special drivers specifically designed for system-level diagnostics to

759

Содержание FAS2600



















































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание FAS2600

Отзывы:

Похожие инструкции для FAS2600

Бренды по названию

Популярные бренды

NetApp FAS2600, Руководство пользователя

Результаты поиска

Содержание FAS2600

Отзывы:

Похожие инструкции для FAS2600

Бренды по названию

Популярные бренды