NetApp FAS2600 Скачать руководство пользователя страница 456 | Manualshive

Страница: 456 / 786

background image

7. If you have not already done so, install the bezel.

Step 4: Install the controller modules

After you install the controller modules into the new chassis, you need to boot it to a state where you can run
the diagnostic test.

For HA pairs with two controller modules in the same chassis, the sequence in which you install the controller
module is especially important because it attempts to reboot as soon as you completely seat it in the chassis.

Steps

1. Align the end of the controller module with the opening in the chassis, and then gently push the controller

module halfway into the system.

Do not completely insert the controller module in the chassis until instructed to do so.

2. Recable the console to the controller module, and then reconnect the management port.

3. Complete the installation of the controller module:

a. Plug the power cord into the power supply, reinstall the power cable locking collar, and then connect

the power supply to the power source.

b. Using the locking latches, firmly push the controller module into the chassis until the locking latches

begin to rise.

Do not use excessive force when sliding the controller module into the chassis to avoid
damaging the connectors.

c. Fully seat the controller module in the chassis by rotating the locking latches upward, tilting them so

that they clear the locking pins, gently push the controller all the way in, and then lower the locking
latches into the locked position.

The controller module begins to boot as soon as it is fully seated in the chassis. Be prepared to
interrupt the boot process.

d. If you have not already done so, reinstall the cable management device.

e. Interrupt the normal boot process and boot to LOADER by pressing

Ctrl-C

.

If your system stops at the boot menu, select the option to boot to LOADER.

f. At the LOADER prompt, enter

bye

to reinitialize the PCIe cards and other components.

g. Interrupt the boot process and boot to the LOADER prompt by pressing

Ctrl-C

.

If your system stops at the boot menu, select the option to boot to LOADER.

4. Repeat the preceding steps to install the second controller into the new chassis.

Complete the restoration and replacement process - FAS8300 and FAS8700

You must verify the HA state of the chassis, run diagnostics, and return the failed part to
NetApp, as described in the RMA instructions shipped with the kit.

454

«
...
454
455
456
457
458
...
»

Содержание FAS2600



















































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для FAS2600

Box Design BT Box S2

Бренд: Pro-Ject Audio Systems Страницы: 6

Бренд: Teufel Страницы: 16

Бренд: Roadstar Страницы: 45

Satmix 2.1 PA system

Бренд: Fun Generation Страницы: 32

Бренд: RCA Страницы: 20

Бренд: Sharp Страницы: 38

Бренд: Sharp Страницы: 54

CMT-M70 Primary

Бренд: Sony Страницы: 1

Бренд: Sony Страницы: 1

Бренд: Sony Страницы: 36

Бренд: Sony Страницы: 36

Бренд: Sony Страницы: 68

CMT-GPX6 - Micro Hifi Component System

Бренд: Sony Страницы: 74

UltraTrak100 TX4

Бренд: Promise Technology Страницы: 54

Бренд: Teac Страницы: 2

Бренд: Audio Technica Страницы: 4

Бренд: Aiwa Страницы: 10

Бренд: Bush Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды