NEC SV8500 Скачать руководство пользователя страница 64

Страница: 64 / 410

– 48 –

CHAPTER 4

OFFICE DATA DESIGN

2.3 Split Data Assignment

STEP 1: ASDT (for Digital terminal such as DT300 Series, Dterm Series

, Dterm Series E/Dterm75)

/AISTL (for IP/SIP terminal such as DT700 Series, DtermIP, IP Enabled Dterm, and Soft Phone)

-Make sure that the agent/supervisory position was already assigned.

STEP 2: ACDPSN -Make sure that the tenant data and the split number were already assigned correctly.

Note:

Be sure that one supervisory position is assigned per split.

STEP 3: ACDSPL -Assign the split data.

TN:

Tenant number (1-9)

SPLIT:

Split number (1-250)

NAME (optional):Name of split (20 characters.)

Note 1

Note 1:

When NAME of route (programmed in ACDTG) or NAME of monitor number (programmed in ACDPLT)
is assigned, skip this parameter.

LOGID:

0/1=Logon ID is not required/Required

AFTER:

0/1=Work/Ready mode after the ACD position is released

ANMD:

0/1=Automatic/Manual operation to answer the ACD calls after logging on

QUEUE FLAG: Unit of Queue flagging

Note 2

0/1=number/percent

Note 2:

QUEUE FLAG=1 (Maximum Queue value is described with the percentage of all agent positions)

QUEUE:

Maximum number of Queue Depth
1-700 for QUEUE FLAG=0
5-1000 for QUEUE FLAG=1

CWCHM:

0/1=Call Waiting Lamp/Chime is not available/Available

WMT:

Work Mode Timer time out (0-9999 sec.)

RMON:

The function of ASSIST key
0/1=Assist/Monitor Me

BRKTP:

0/1=Break mode is not available/Available

NIGHT:

Night destination (Max. 5 digits)

Note 3

ASIST:

Assistance call destination. (Max. 5 digits)

Note 3

EMGCY:

Emergency call destination. (Max. 5 digits)

Note 3

RECD:

Recorder equipment number (0-5, 0 = Recorder equipment is not used)

Note 3

Note 3:

This data is valid when CCV is designated for the procedure of handling ACD call (CCV/W=0 in ACD-
PLT).

DNDS:

0/1=DO NOT DISTURB - SPLIT is available/Not available

Note 4

Note 4:

Assign 1 to reject ACD call queuing when all agents have been logged off in the split.

WKRST:

0/1=Work mode is available/Not available

AWPI:

Work mode for the ACD call when connecting with a non-ACD call
0=Work Mode is not available
1=Available when the non-ACD call is terminated
2=Available when the non-ACD call is answered
3=Available when the non-ACD call is terminated/answered

AWPO:

Work mode for the ACD call when originating a non-ACD call
0/1=Not available/Available

Содержание SV8500



























































































































































































































































































































































































































Результаты поиска

Содержание SV8500

Отзывы:

Похожие инструкции для SV8500

Бренды по названию

Популярные бренды

NEC SV8500, Руководство по программированию

Результаты поиска

Содержание SV8500

Отзывы:

Похожие инструкции для SV8500

Бренды по названию

Популярные бренды