NEC SV8500 Скачать руководство пользователя страница 406

Страница: 406 / 410

– 8 –

APPENDIX B FIELD VALUES FOR ACD SCREENS

Operator
access code

Defines the access code programmed for the operator in the
Node database.

up to 5

digits

required

Outbound call
answer timer

Time allowed for outbound calls to be considered
successfully completed

0 ~ 60 sec-

onds

required

Overflow
timeout

Defines how long a call will stay in queue to the personal
pilot number before it overflows. (0 = Indefinite.)

0 ~ 9999

none

required

PBX incoming Specifies whether agents should be forced into Work mode

upon receiving an incoming call on their Non-ACD line.

Yes/No

required

PBX outgoing Specifies whether agents should be forced into Work mode

upon receiving dial tone for an outgoing call on their Non-
ACD line.

Yes/No

required

Personal assist
request
number

Overrides the assist request number programmed in
ACDSPL.

up to 5

digits

none

optional

Personal
emergency
request
number

Overrides the emergency request number programmed in
ACDSPL.

up to 5

digits

none

optional

Personal pilot
number

Defines the number programmed in AMNO/AMNOL/
AMNON. (Not programmed in ACDPLT.)

up to 5

digits

none

optional

Personal
queue
announcement
number

Defines the announcement used for calls directed to personal
queue (for the entire tenant).

1 ~ 58

none

optional

Personal
queue
overflow/
forward
priority

Defines the priority for calls that overflow from a personal
queue.

1 ~ 250

optional

Pilot name

Name displayed when a call is answered at positions.

up to 20

characters

blank

optional

Pilot number
(ACDPLT)

A directory number that calls can be presented to. (Personal
pilot numbers are not programmed here.)

up to 5

digits

none

required

Position

The My Line of the ACD position.

up to 5

digits

none

required

Queue priority Priority at which a call from this trunk group (route) is placed

in the queue.

1 (high) ~

250 (low)

required

Table B-1 Field Values for ACD Screens (6 of 8)

FIELD NAME

DESCRIPTION

VALUES

DEFAULT

SETTING

REQUIRED

/OPTIONAL

Содержание SV8500



























































































































































































































































































































































































































Результаты поиска

Содержание SV8500

Отзывы:

Похожие инструкции для SV8500

Бренды по названию

Популярные бренды

NEC SV8500, Руководство по программированию

Результаты поиска

Содержание SV8500

Отзывы:

Похожие инструкции для SV8500

Бренды по названию

Популярные бренды