NEC SV8500 Скачать руководство пользователя страница 292

Страница: 292 / 410

– 276 –

CHAPTER 5

ACD SERVICE FEATURES FUNCTIONAL TEST PROCEDURES

Note:

After MON key is pressed, “BARGE?” is displayed. At that time, monitoring is abandoned by one of the
following operations.

•

Dial “1” + “#” or “1” + “n” ... “n” + “#”

•

Press MON key again

•

No operation for 30 seconds

NAP-215-108

Sheet 2/2

Emergency Recorder

Answering by supervisory position.
• The supervisory position answers the call as an ACD call and monitors it (three-party conference call

does not occur).

• The agent position can confirm the answering of the supervisory position by the change of the lamp

indication on the agent position (flashing steady) as well as from the LCD display.

Confirmation of recording.
• Check that the call is recorded by the recorder.

The supervisory position presses the MON key to start three-party conference call.

Note

Release by ACD agent position.
• When the agent position releases the incoming C.O. trunk call, it is transferred to the supervisory posi-

tion.

Confirmation of communication.
• Check that the supervisory position is communicating with the C.O. trunk.

Release by supervisory position.

Apply the test procedure above to all splits.

END

Содержание SV8500



























































































































































































































































































































































































































Результаты поиска

Содержание SV8500

Отзывы:

Похожие инструкции для SV8500

Бренды по названию

Популярные бренды

NEC SV8500, Руководство по программированию

Результаты поиска

Содержание SV8500

Отзывы:

Похожие инструкции для SV8500

Бренды по названию

Популярные бренды