NEC SV8500 Скачать руководство пользователя страница 321 | Manualshive

Страница: 321 / 410

background image

– 305 –

ACDPSN : Assignment of ACD Position Data

ACDPSN: Assignment of ACD Position Data

1.

Function

This command is used to assign, display, print, and remove ACD position data. Each position is identified
by the tenant it belongs to, the number of its ACD line and the Non-ACD line it may have, and what split(s)
the position belongs to.

2.

Precautions

(1) The terms supervisor and agent are used as a convention but are not differentiated by the ACD system.
(2) Any position may have a

NIGHT

key.

(3) Removing positions removes them as ACD agents or supervisors. Positions still function as Non-ACD

lines unless removed using ASDT/AISTL (see Data Programming Sheets).

(4) If changing the Tenant Number, My Line number, or ACD line number with the ASDT/AISTL/ASTN

commands (Node), the position must first be deleted using the ACDPSN command, before changes
using the ASDT/AISTL/ASTN commands may be made. See the procedure below.
STEP 1: Delete the ACDPSN data of ACD agent/supervisory position to be changed the number.
STEP 2: Change the number using ASDT/AISTL or ALGSL/ALGSN.
STEP 3: Assign the changed number and other data in the ACDPSN data.

(5) For maximum number of ACD positions per ACD system, see Section 2.3.1 ACD System Capacity

in CHAPTER 2.

(6) If an invalid Node or ACD line number is programmed in ACDSPN, it may cause erroneous CW lamp

problems.

(7) There should only be two lines on an ACD position (the My line and the ACD line). If other lines are

programmed on an ACD position, the MIS status may be incorrect.

(8) Do not allow Call Pickup to ACD lines (may cause incorrect MIS status).
(9) One of the following conditions must be agreed when using this command

• ACD line number and Non-ACD line number is assigned using the ASDT/AISTL command
• ACD line number and Non-ACD line number is assigned using the ALGSL command
• ACD line number and Non-ACD line number is assigned using the ALGSN command

(10) When assigning PTYPE is 2~4, data entry to ACDL is not necessary. The Non-ACD line number as-

signed in NACD is automatically entered in ACDL in this case.

«
...
319
320
321
322
323
...
»

Содержание SV8500



























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SV8500

Express5800/T110g-S

Бренд: NEC Страницы: 34

Бренд: Gateway Страницы: 138

Бренд: IBM Страницы: 84

Бренд: IBM Страницы: 110

HS12 - BladeCenter - 8028

Бренд: IBM Страницы: 204

Бренд: IESC Страницы: 109

Бренд: Watchguard Страницы: 32

CE-HE130S4 Series

Бренд: Ablecom Страницы: 43

SuperServer E300-9C

Бренд: Supermicro Страницы: 113

Бренд: Patton Страницы: 15

SC450NX - Server Platform - 0 MB RAM

Бренд: Intel Страницы: 200

Rackmount 5000 Series

Бренд: Johnson Controls Страницы: 42

VGF-HS1 - Vaio Home Server

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 28

Бренд: Sony Страницы: 313

Бренд: BCDVideo Страницы: 157

Бренд: QSSC Страницы: 97

Access Server M

Бренд: SSS Siedle Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды