NEC SV8500 Скачать руководство пользователя страница 202 | Manualshive

Страница: 202 / 410

background image

– 186 –

M-28A MONITORING - ACD SUPERVISOR - ACD

M-28A MONITORING - ACD SUPERVISOR - ACD

GENERAL DESCRIPTION

This feature allows the supervisor to select an agent position and to monitor the calls on both the ACD line and the
non-ACD line at that position. The agent and calling party are not aware that their call is being monitored. As the
agent concludes one call and begins another, switches from one line to another, or transfers, the supervisor’s monitor
is applied to the current call. If both lines are idle when the monitoring is established, the supervisor will hear quiet
tone until the agent either answers a call on one of the lines or places a call from the non-ACD line. At that time, the
supervisor will be able to hear both parties. This feature has been available for network that is configured by Peer-
to-Peer FCCS. VS-32 can also be used for this feature.

OPERATING PROCEDURE

•

While an agent position is busy.

STEP 1: Lift the handset.

STEP 2: Press the

MON/BARGE

key.

STEP 3: Dial “Station ID code + #” or “0 + Station Number for A Call of Agent Po #”.

STEP 4: Supervisory Position starts monitoring the call between the Agent Position and the ACD call.

STEP 5: Press the

RELEASE

key.

•

While an agent position is in a state other than busy.

STEP 1: Lift the handset.

STEP 2: Press the

MON/BARGE

key.

STEP 3: Dial “Station ID code + #” or “0 + Station Number for A Call of Agent Po #”.

STEP 4: The Agent Position is set to be monitored.

STEP 5: Replace the handset.

STEP 6: The Supervisory Position is called when the Agent Position start talking.

STEP 7: Lift the handset.

STEP 8: The Supervisory Position starts monitoring the call between the Agent Position and the ACD call.

STEP 9: Press the

RELEASE

key.

Note:

The

MON/BARGE

lamp will flash while monitoring, and light while being set ready to start moni-

toring. Also, the lamp will flash while the Supervisory Position is hearing a held tone provided
when the monitored call is held or transferred.

SERVICE CONDITIONS

1. Three-way conference trunk or VS-32 is required for this feature.

«
...
200
201
202
203
204
...
»

Содержание SV8500



























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SV8500

Бренд: TYAN Страницы: 109

Бренд: ACTi Страницы: 15

UniServer R4300 G5

Бренд: H3C Страницы: 16

Бренд: AIC Страницы: 101

SUPERSERVER 2048U-RTR4

Бренд: Supermicro Страницы: 152

SuperServer E300-9C

Бренд: Supermicro Страницы: 113

SuperServer E301-9D-8CN8TP

Бренд: Supermicro Страницы: 117

Бренд: NEC Страницы: 138

Бренд: Gigabyte Страницы: 120

IP-DECT SERVER 6500

Бренд: SpectraLink Страницы: 2

Бренд: KVH Industries Страницы: 2

SDSTX3110-121S-LRT

Бренд: Transition Networks Страницы: 109

WF01 64 V2 Series

Бренд: Lanberg Страницы: 22

Бренд: Lantronix Страницы: 110

Бренд: Wiredocean Страницы: 36

ETHERNETV 4410-0118-0009

Бренд: VBrick Systems Страницы: 202

Бренд: Intel Страницы: 233

Бренд: Gigabyte Страницы: 114

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды