NEC SV8500 Скачать руководство пользователя страница 216

Страница: 216 / 410

– 200 –

M-79A MULTIPLE SUPERVISORS - ACD

GENERAL DESCRIPTION

Multiple supervisors can be grouped together to form a split when it is necessary for more than one supervisor to

serve a split of agents. Assistance and emergency requests can be routed to a split of supervisors, but a split of su-

pervisors does not normally receive incoming call traffic unless it has been programmed as a secondary split to be

queued to in a Call Control Vector (CCV). Refer to “CALL CONTROL VECTOR-ACD [C-108A]” for more de-

tailed information. All aspects of an agent split, such as call waiting indication and queuing, also apply to a split of

supervisors.

OPERATING PROCEDURE

For additional reading please see the note for “The Supervisor Concept” in SPLIT-ACD [S-91A].

SERVICE CONDITIONS

1. Assistance and emergency calls with this feature can not be taken by the supervisor in Work Mode or Ready

Mode (Assistance and emergency call to a individual supervisor can be taken by supervisors in those modes).

2. The followings are differences between assistance/emergency requests to an individual supervisor and those to

a split of supervisors. See “ASSISTANCE - ACD AGENT-ACD [A-34A]” and “EMERGENCY/RECORDER-

ACD [E-6A]” for more details.

3. CCV data programmed for a pilot number of a split of supervisors as the destination of Assistance call or Emer-

gency call is as follows. See Section 2.7 in CHAPTER 4 “CCV Assignment”.
•Queue Assign, Conditional Queue Assign

•Pause (Valid for CCV data for Assistance only)

•End CCV

4. Since DAY/NIGHT CLASS OF SERVICE [D-15] can not be used for the split of supervisors, do not set the

data that ACD call excluding Assistance and Emergency calls terminated to the split directly.

5. When using dictation trunk for EMERGENCY/RECORDER, recording starts from the moment the call termi-

nates to the supervisory position (It is not recorded while the call is in queue).

6. When emergency request call is routed to a specified Split of Supervisors, the emergency request call cannot be

canceled by pressing the EMER key. Release operation of the appropriate Supervisor or the monitored Agent
can cancel the emergency request call.

Destination

Service

Individual Supervisor

Split of Supervisor

Assistance-ACD Agent

Assistance call terminates to Non-ACD
line to the supervisor

Assistance call terminates to the pilot
number of the split

Emergency/Recorder

Emergency call can be distributed to the
supervisor in Work Mode/Ready Mode.

Emergency call can not be distributed to
the supervisor in Work Mode/Ready
Mode.

Содержание SV8500



























































































































































































































































































































































































































Результаты поиска

Содержание SV8500

Отзывы:

Похожие инструкции для SV8500

Бренды по названию

Популярные бренды

NEC SV8500, Руководство по программированию

Результаты поиска

Содержание SV8500

Отзывы:

Похожие инструкции для SV8500

Бренды по названию

Популярные бренды