NEC PD703114 Скачать руководство пользователя страница 127

Страница: 127 / 692

CHAPTER 6 DMA FUNCTIONS (DMA CONTROLLER)

127

User’s Manual U15195EJ5V0UD

6.9 DMA Transfer Start Factors

There are two types of DMA transfer start factors, as shown below.

Cautions 1. Do not use both start factors ((1) and (2)) in combination for the same channel (if these two

start factors are generated at the same time, only one of them is valid, but the valid start

factor cannot be identified).

The operation is not guaranteed if two start factors are used in combination.

2. If DMA transfer is started via software and if the software does not correctly detect whether

the expected DMA transfer operation has been completed through manipulation (setting to 1)

of the STGn bit of the DCHCn register, it cannot be guaranteed whether the next (second)

manipulation of the STGn bit corresponds to the start of “the next DMA transfer expected by

software” (n = 0 to 3).

For example, suppose single transfer is started by manipulating the STGn bit. Even if the

STGn bit is manipulated next (the second time) without checking by software whether the

single transfer has actually been executed, the next (second) DMA transfer is not always

executed. This is because the STGn bit may be manipulated the second time before the first

DMA transfer is started or completed because, for example, DMA transfer with a higher

priority had already been started when the STGn bit was manipulated for the first time.

It is therefore necessary to manipulate the STGn bit next time (the second time) after

checking whether DMA transfer started by the first manipulation of the STGn bit has been

completed.

Completion of DMA transfer can be checked by confirming the contents of the DBCn register.

(1) Request from software

If the STGn, Enn, and TCn bits of the DCHCn register are set as follows, DMA transfer starts (n = 0 to 3).

•

STGn bit = 1

•

Enn bit = 1

•

TCn bit = 0

(2) Request from on-chip peripheral I/O

If, when the Enn and TCn bits of the DCHCn register are set as shown below, an interrupt request is issued

from the on-chip peripheral I/O that is set in the DTFRn register, DMA transfer starts (n = 0 to 3).

•

Enn bit = 1

•

TCn bit = 0

Содержание PD703114





















































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание PD703114

Отзывы:

Похожие инструкции для PD703114

Бренды по названию

Популярные бренды

NEC PD703114, Руководство пользователя

Результаты поиска

Содержание PD703114

Отзывы:

Похожие инструкции для PD703114

Бренды по названию

Популярные бренды