MUTOH VJ-626UF Скачать руководство пользователя

Страница: 122 / 144

122 Moving the printer

Moving and Transporting

Please refer to this section when moving or transporting this printer.

When moving this printer, it is necessary to empty the waste ink tank.
Moving without emptying the tank can cause ink leakage.

After moving, reinstall the printer.

• This procedure requires four or more people.

• Keep this printer level when moving it.

Important!

• When moving this printer, always empty the waste ink tank even moving short distance.

If ink splashes inside the waste ink tank while being moved, it can cause damage.

• Do not tilt, set against something or place this printer upside down.

Otherwise the ink may leak or the handling mentioned above may cause abnormality.

Moving the printer

Preparation before moving

[1]

Empty the waste ink tank.

"Emptying waste ink tank" on page 96

[2]

Reset the waste ink counter.

"Resetting waste ink counter" on page 98

[3]

Turn the printer OFF, then remove all the cables from the printer.

[4]

Move the printer.

Installation after moving

[1]

Select a suitable place for installation.

“Startup Guide”

[2]

Plug cables into the printer.

[3]

Move the printer to the installation area and level the printer.

“Startup Guide”

[4]

Perform Nozzle check, and then check that there is no clogging in Print head.

"Nozzle check and cleaning" on page 37

Moving and Transporting

CAUTION

Содержание VJ-626UF

















































































































































Результаты поиска

Содержание VJ-626UF

Отзывы:

Похожие инструкции для VJ-626UF

Бренды по названию

Популярные бренды

MUTOH VJ-626UF, Руководство по эксплуатации

Результаты поиска

Содержание VJ-626UF

Отзывы:

Похожие инструкции для VJ-626UF

Бренды по названию

Популярные бренды