MUTOH VJ-626UF Скачать руководство пользователя | Manualshive

Страница: 134 / 144

background image

134 Error requiring restart

An error requiring restart is displayed if a fatal operational failure such as the following occurs.

• When an obstacle that prevents printing occurs.

• When a problem occurs with the electrical circuit (PCB, motor, sensor, etc.) of the printer

.

• When a failure in the printer control program occurs.

If an error requiring restart occurs, the printer stops operating after performing the following operations.

1. The drive power automatically shuts down.

2. All LED lights on the operation panel blink and the printer beeps continuously.

3. The error message is displayed on the operation panel.

Pressing any key on the operation panel stops the beeping.
For an error requiring restart, operation will return to normal after removing the cause of the error and restarting the printer.
If the same error message is repeatedly displayed, contact the your local MUTOH dealer.
Be sure to tell us the code no. of the error message when you contact us.

Note

“ *** “ in the error message is the code no. that indicates what type of error occurred.

Error requiring restart

Display

Description

Emergency Mode: E ***

A problem that does not have a remedy has occurred.

1. Check if the replaced parts are installed correctly.

2. Turn the power button off. Wait a short while, then turn the power

button on, to restart the printer.

Emergency Mode: AC

The power was shut down instantaneously while the printer is operating.

1. Turn the power button off. Wait a short while, then turn the power

button on, to restart the printer.

Emergency Mode: CPU

CPU error occurred.

1. Turn the power button off. Wait a short while, then turn the power

button on, to restart the printer.

«
...
132
133
134
135
136
...
»

Содержание VJ-626UF

















































































































































Отзывы:

Нет отзывов

Похожие инструкции для VJ-626UF

Бренд: Oki Страницы: 40

Бренд: Panasonic Страницы: 9

Бренд: Panasonic Страницы: 2

Бренд: IBM Страницы: 334

Бренд: IBM Страницы: 428

Бренд: IBM Страницы: 316

Бренд: IBM Страницы: 210

Magicolor 2 plus

Бренд: QMS Страницы: 90

Magicolor 2 Desklaser

Бренд: QMS Страницы: 4

Бренд: QMS Страницы: 8

Бренд: QMS Страницы: 94

Бренд: QMS Страницы: 6

Бренд: Unimark Страницы: 36

Бренд: Xerox Страницы: 44

Бренд: Oki Страницы: 76

Бренд: Felix printers Страницы: 28

Бренд: Rapid Shape Страницы: 44

Бренд: Linux Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды