MUTOH VJ-626UF Скачать руководство пользователя

Страница: 66 / 144

66 Set 1: User Type

PF4. Micro Print

• Observe the pattern and verify the micro adjustment value. In the pattern, look for a place that has least white lines or

overlapping in images. The number printed below the pattern is the micro adjustment value.

• Enter the Micro adjustment value according to the test pattern print.

PF5. Micro Change

Performs Micro adjustment print.
Enter the appropriate micro adjustment value according to the test pattern
print.

Note

The micro adjustment value saved becomes the pattern’s standard value.

For example, if “-0.20” is saved as the micro adjustment value and a pattern is printed again, the number below the center pattern changes

from “0.00” to “-0.20”, and the left edge to “+0.30” and right edge to “-0.70”.

Use the [+] / [ - ] key to enter the micro adjustment value, and press the [Enter]
key.

Setting values

-5.00% to <0.00%> to 5.00%
<> indicates the default setting.

**>4: Vacuum Fan

Sets up vacuum fan operation. It has the role of fixing the media to the table.

• If you are using a thin or delicate media and there is risk of it wrinkling due to

the fan, set a lower value for the fan.

Setting values

High / Medium-Hi / <Medium>/ Low / Off
<> indicates the default setting.

PF4 :

Micro Print

-0.50

-0.20

-0.10

0.00

+0.10

+0.20

+0.50

-0.50

-0.10

-0.20

Micro adjustment value

Not adequate

Adequate

Not adequate

PF5 :

Micro Change

Micro :

5.00%

**> 4 :

Vacuum Fan

Vacuum Fan :

High

Содержание VJ-626UF

















































































































































Результаты поиска

Содержание VJ-626UF

Отзывы:

Похожие инструкции для VJ-626UF

Бренды по названию

Популярные бренды

MUTOH VJ-626UF, Руководство по эксплуатации

Результаты поиска

Содержание VJ-626UF

Отзывы:

Похожие инструкции для VJ-626UF

Бренды по названию

Популярные бренды