MUTOH VJ-626UF Скачать руководство пользователя | Manualshive

Страница: 92 / 144

background image

92 Agitating ink cartridges

3

Agitating ink cartridges

Agitate the ink at the following times to prevent it from settling out and/or coagulating:

• Before installing new ink cartridge

• When any of the messages below appears

6-color configuration:

4-color configuration:

Agitating ink cartridges

Agitate the White (Wh) ink cartridge.

• Displays every 12 hours.

Agitate the Black (K), Magenta (M), Cyan (C), and Yellow (Y) ink
cartridges.

• Displays every 72 hours.

Agitate the Black (K), Magenta (M), Cyan (C), Yellow (Y), and White
(Wh) ink cartridges.

Agitate the Black (K), Magenta (M), Cyan (C), and Yellow (Y) ink
cartridges.

• Displays every 72 hours.

Important!

• Agitate the ink cartridges periodically.

Otherwise, the ink inside the cartridges settles or coagulates and may cause poor print quality or a malfunction.

• You should agitate the ink cartridges when the message appears. Otherwise, for 12 hours after the message appears, you will

repeatedly have to wait a certain time before you can print.
When 12 hours have passed, the printer will not print any data. In either case, you can restore the printer to normal condition by
agitating the ink cartridges.

Skin or eye contact with UV curable ink may cause skin inflammation or allergic reaction.

For this operation, be sure to wear the supplied gloves (or solvent resistant gloves) and goggles to prevent ink from contacting
with your eyes or skin.

Agitating ink cartridges

Shake W Cartridge

Shake KMCY Cartridge

Shake KMCYW Cart.

Shake ALL Cart.

CAUTION

«
...
90
91
92
93
94
...
»

Содержание VJ-626UF

















































































































































Отзывы:

Нет отзывов

Похожие инструкции для VJ-626UF

Бренд: WaxJet Страницы: 131

Бренд: Xerox Страницы: 73

Бренд: Xerox Страницы: 2

Бренд: Canon Страницы: 2

Бренд: Seiko Страницы: 76

Бренд: A&D Страницы: 66

Бренд: 3nStar Страницы: 8

Бренд: Ricoh Страницы: 2

Бренд: Panduit Страницы: 85

Бренд: HandTop Страницы: 97

Бренд: Sartorius Страницы: 202

Бренд: Brother Страницы: 93

Бренд: Canon Страницы: 28

Бренд: Canon Страницы: 4

Бренд: Canon Страницы: 2

Бренд: Canon Страницы: 20

Бренд: Canon Страницы: 31

Бренд: Canon Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды