MUTOH VJ-626UF Скачать руководство пользователя | Manualshive

Страница: 131 / 144

background image

Error message display and possible solutions 131

This section describes error messages and possible solutions.
Error messages are displayed when certain failures occur during printer operation.
If an error that can be displayed occurs, the printer may display the following error messages on the operation panel and stop
operation.

Empty WasteInk ->E

Transfer the waste fluid from the waste ink tank into a container, and press
the [Enter] key.

"Emptying waste ink tank" on page 96

Perform Daily Maint.

Make sure to perform daily maintenance when prompted.

"Clean daily maintenance parts" on page 109

Error message display and possible solutions

Display

Description

Cover Open

The front cover is open.
Close the front cover.

Maint. Cover Open

The maintenance cover is open.
Close the maintenance cover.

[******] Ink End

Ink has run out. (Stops operation)
Replace with a new ink cartridge.

"Replacing ink cartridge" on page 95

[******] NoCartridge

Ink cartridge is not inserted. (Stops operation)
Insert Ink cartridge.

[*******] Discharged

Ink is not filled.
Perform initial ink charging.

"How to perform initial ink charging after ink discharge" on page

Full WasteInkTank

The waste ink tank has become full.
(Operation will stop when this happens.)
Immediately transfer the waste fluid into a container.

"Emptying waste ink tank" on page 96

NearFullWasteInkTank

The waste ink tank is about to become full.
(Operation will continue in this condition.)
Transfer the waste fluid into a container.

"Emptying waste ink tank" on page 96

[*] Ink Low

Slot * ink is low.
Get a replacement cartridge ready.

[******] S/C ReadErr

Reading S/C Card has been failed.
Insert ink cartridge again. If S/C Card still cannot be read, insert new ink
cartridge.

[******] S/C Col.Err

Ink cartridges are inserted in wrong slots.
Insert ink cartridges correctly again.

[*] S/C Ink Err

The ink cartridge cannot be used for this printer.
Contact your local MUTOH dealer.

[*] S/C CodeErr

Inserted ink cartridge is not a proper one.
Contact your local MUTOH dealer.

[*] Broken Chip

S/C Card has been broken.Insert new ink cartridge.

Display

Description

«
...
129
130
131
132
133
...
»

Содержание VJ-626UF

















































































































































Отзывы:

Нет отзывов

Похожие инструкции для VJ-626UF

Бренд: QMS Страницы: 160

Бренд: QMS Страницы: 110

Бренд: QMS Страницы: 158

Бренд: CAB Страницы: 144

Бренд: OKIDATA Страницы: 13

Бренд: Oki Страницы: 189

Бренд: Zebra Страницы: 29

Бренд: Dascom Страницы: 146

Бренд: Wang Страницы: 181

Бренд: Loadrite Страницы: 12

Бренд: Cisco Страницы: 43

Бренд: MINOLTA-QMS Страницы: 67

Бренд: Utax Страницы: 94

Бренд: Custom Audio Electronics Страницы: 26

Бренд: Custom Audio Electronics Страницы: 30

Бренд: BEINAT Страницы: 4

Бренд: Jingda Страницы: 12

TELEIOS GRANDE H6

Бренд: d.gen Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды