MUTOH VJ-626UF Скачать руководство пользователя

Страница: 128 / 144

128 How to perform initial ink charging after ink discharge

How to perform initial ink charging after ink discharge

[1]

Turn the power button of this printer ON.

• Blue light turns on.

• The printer starts initialization operations.

[2]

Press the “Enter” key when the message on the left appears.

[3]

When the message on the left appears, empty the waste ink tank.

"Drain waste fluid into container" on page 97

[4]

• Press the [Enter] key.

• The message on the left will appear.

[5]

Make sure you agitate the ink cartridge after you unpack it.

• Turn the ink plug upward and wait for three seconds.

• Next, turn the ink plug downward and wait for three seconds.

• Repeat that 10 times.

Note

You do not have to agitate varnish ink before use.

[6]

Insert ink cartridge to this printer.

• Match the label of this printer to the color of ink cartridge.
• The arrow should face up.
• Insert all the way to the end.

Important!

Load the same ink color configuration as before.

The message on the left will appear.

• This printer starts ink charging.

During ink charging, make sure:

• Not to turn OFF the printer.

• Not to unplug the power cable of the printer.

• Not to open the front cover.

• Not to open the maintenance cover.

When ink charging is complete, the message on the left will appear.

Option

Press!

Start Ink Charge

- > E

Empty WasteInk

- > E

Insert InkCartridges

x 10

3 sec.

slot 1

Ink

Charge

**%

CAUTION

Set Media, then

press Set Media key.

Содержание VJ-626UF

















































































































































Результаты поиска

Содержание VJ-626UF

Отзывы:

Похожие инструкции для VJ-626UF

Бренды по названию

Популярные бренды

MUTOH VJ-626UF, Руководство по эксплуатации

Результаты поиска

Содержание VJ-626UF

Отзывы:

Похожие инструкции для VJ-626UF

Бренды по названию

Популярные бренды