MUTOH VJ-626UF Скачать руководство пользователя | Manualshive

Страница: 113 / 144

background image

Inside cleaning 113

Preparation:

• Paper Towel (Lint-free cloth) or Polyester knit wiper (optional)

• Lubricating grease

• Cleaning stick

3.

Table Maintenance

Important!

During cleaning, please note the followings.

• DO NOT apply lubricating grease on area other than specified.

• Always use the paper towel (lint-free cloth) supplied with the printer or optional polyester knit wiper.

DO NOT use tissue paper.

Before greasing

[1]

If any media or jig is loaded on the table, open the front cover and remove it.

[2]

Check that the front cover is closed, and press the [Menu] key.

[3]

• Press the [ - ] key until “Menu 3: Maintenance >” appears.

• Press the [>] key.

[4]

• Press the [ - ] key until “Mnt.8: Table Maint.” appears.

• Press the [Enter] key.

[5]

The message on the left will appear.

• Press the [Enter] key.

The message on the left will appear.

• The table moves to the front side of the printer.

[6]

The message on the left will appear.

• Remove the media and the jig on the table, and then press the

[Enter] key.

The message on the left will appear.

• The table moves to the position to perform the screw shaft

maintenance.

[7]

The message on the left will appear.

• You can start table maintenance.

1

2

Set Media

Remove Media

Media Set

Low speed

Press!

Menu 3 :

Maintenance >

Mnt. 8 :

Table Maint.

Table Maint. :

Start

Wait for a while

Remove

Media

->

Enter

Wait for a while

Table Maint. :

End

«
...
111
112
113
114
115
...
»

Содержание VJ-626UF

















































































































































Отзывы:

Нет отзывов

Похожие инструкции для VJ-626UF

Бренд: WaxJet Страницы: 131

Бренд: EasyThreed Страницы: 15

Бренд: EBS Страницы: 34

Бренд: FELIXprinters Страницы: 66

Бренд: Afinia 3D Страницы: 47

Бренд: Alunar Страницы: 6

Бренд: Rapid Shape Страницы: 44

Бренд: Linux Страницы: 8

Genmitsu 3018-MX3

Бренд: SainSmart Страницы: 50

Бренд: Aleph Objects Страницы: 26

Executive Series 3037

Бренд: Oki Страницы: 546

Бренд: Citizen Страницы: 255

Бренд: DURACARD Страницы: 31

Бренд: MostFun Страницы: 25

Бренд: Canon Страницы: 37

Бренд: Canon Страницы: 83

Бренд: Canon Страницы: 1068

Бренд: Canon Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды