MUTOH VJ-626UF Скачать руководство пользователя

Страница: 26 / 144

26 Precautions when using this printer

To access to the wiper and the head cap unit for daily maintenance, you can open and close the maintenance cover on this

printer.

Safety precautions to open and close the front cover and the maintenance cover

•

Do not open or close the cover while you are off balance.

You may pinch your finger or get injured.

• Hold the handle of the front cover and gently open or close the cover.

If excessive force is applied to the cover, it will shorten its life or will damage to the printer.

• Always fully open the maintenance cover.

If you leave it half-open, the maintenance cover can suddenly close.

• When closing the maintenance cover, hold the tab on the maintenance cover to gently close it.

Do not place your fingers on the edges of the printer’s opening portion, or on any parts around those edges.
Your fingers could get caught and be injured.

Hold the handle on the front cover to gently open it.

Hold the position shown on the left and gently close the cover.

Hold the tab on the maintenance cover as shown on the left to gently
open or close the cover.

CAUTION

Содержание VJ-626UF

















































































































































Результаты поиска

Содержание VJ-626UF

Отзывы:

Похожие инструкции для VJ-626UF

Бренды по названию

Популярные бренды

MUTOH VJ-626UF, Руководство по эксплуатации

Результаты поиска

Содержание VJ-626UF

Отзывы:

Похожие инструкции для VJ-626UF

Бренды по названию

Популярные бренды