MUTOH VJ-626UF Скачать руководство пользователя

Страница: 25 / 144

Precautions when using this printer 25

Use the printer with its power turned permanently on. When you are not using the printer, always leave the power on and put

the printer into the sleep mode while not in use. In the sleep mode, the printer will periodically circulate the ink inside the printer

and carry out head cleaning automatically. If you do not put the printer into the sleep mode, the ink inside the printer could

settle out and/or coagulate, causing poor image quality or printer failure.

Before installing a new ink cartridge, invert the ink cartridge back and forth to agitate ink. Periodical ink agitation is also required

when prompted on the operation panel.

Otherwise, the ink inside the cartridges settles or coagulates and may cause poor print quality or a malfunction.

It is recommended to use this printer at least once a week. When left unused for a long time, the print head nozzles can get

clogged causing damage to the printer.

This printer requires daily maintenance.

• Perform the Nozzle check before and after printing.

If nozzle clog is found, perform a head cleaning.

• Make sure to perform daily maintenance after you finish printing for the day.

Failure to perform daily maintenance may affect print quality or result in damage to the printer.

"Daily Maintenance" on page 99

• Empty the waste ink tank when needed.

• Clean the interior of the printer once a month.

In this printer, following parts need to be replaced after a long-term use.

• Parts required to be replaced by users: Absorption material for the flushing box, Cleaning wiper

• Parts required to be replaced by service personnel: Various motors, pumps, Print head, Head cap unit, the UV lamp

Precautions when using this printer

Do not turn the power off

Agitate the ink cartridges

Please use this printer periodically

Conduct periodic maintenance

Some parts need to be replaced periodically

Содержание VJ-626UF

















































































































































Результаты поиска

Содержание VJ-626UF

Отзывы:

Похожие инструкции для VJ-626UF

Бренды по названию

Популярные бренды

MUTOH VJ-626UF, Руководство по эксплуатации

Результаты поиска

Содержание VJ-626UF

Отзывы:

Похожие инструкции для VJ-626UF

Бренды по названию

Популярные бренды