MUTOH VJ-626UF Скачать руководство пользователя

Страница: 105 / 144

Performing Daily Maintenance 105

Cleaning of cleaning wiper and the circumference of the cap

[1]

Hold the tab on the maintenance cover as shown on the left to gently
open the cover.

• Fully open the maintenance cover.

[2]

Wipe the cleaning wiper with a cleaning stick.

• Wipe the left side surface of cleaning wiper going back and forth.

[3]

Wipe the right side surface of cleaning wiper going back and forth.

[4]

Use the cleaning stick to remove the ink and dust on the
circumference of the cap.

[5]

Close the maintenance cover gently.

[6]

Next finish the daily maintenance.

DO NOT touch the absorber
(the yellow portions in the illustration right)

Cleaning required

Содержание VJ-626UF

















































































































































Результаты поиска

Содержание VJ-626UF

Отзывы:

Похожие инструкции для VJ-626UF

Бренды по названию

Популярные бренды

MUTOH VJ-626UF, Руководство по эксплуатации

Результаты поиска

Содержание VJ-626UF

Отзывы:

Похожие инструкции для VJ-626UF

Бренды по названию

Популярные бренды