MUTOH VJ-626UF Скачать руководство пользователя

Страница: 41 / 144

Starting printing 41

You can lay out and print out the images using the bundled CD-ROM software, Layout and Print Tool 2.

This section explains the basic printing instructions only. For the details, see the operation manual for Layout and Print Tool 2.

Layout and Print Tool 2 supports following graphic file formats:

• PNG (.png)

• TIFF (.tif )

Starting printing

Printing from the Layout and Print Tool 2

Note

For the details of supported file format, see the Layout and Print Tool 2 Operation Manual.

[1]

Start Layout and Print Tool 2.

"Launching Layout and Print Tool 2" on page 22

[2]

Select the printer driver.

• Click [Apply].

[3]

If the driver settings have not been completed, the dialog on the left
will appear.

• Click [OK].

[4]

The dialog on the left will appear.

• Click [OK].

[5]

Select the image to be used in printing.

•

Click the

button to insert the image.

Содержание VJ-626UF

















































































































































Результаты поиска

Содержание VJ-626UF

Отзывы:

Похожие инструкции для VJ-626UF

Бренды по названию

Популярные бренды

MUTOH VJ-626UF, Руководство по эксплуатации

Результаты поиска

Содержание VJ-626UF

Отзывы:

Похожие инструкции для VJ-626UF

Бренды по названию

Популярные бренды