MUTOH VJ-626UF Скачать руководство пользователя

Страница: 117 / 144

Replacing absorption material for the flushing box 117

[3]

Hold the tab on the maintenance cover as shown on the left to gently
close the cover.

When closing the maintenance cover, hold the tab on the maintenance cover to gently close it.

Do not place your fingers on the edges of the printer’s opening portion, or on any parts around those edges. Your fingers could
get caught and be injured.

Replacing steps

[1]

Check that no object including a jig is loaded on the table.

[2]

Press the [Menu] key.

[3]

• Press the [ - ] key until “Menu 3: Maintenance >” appears.

• Press the [>] key.

[4]

• Press the [ - ] key until “Mnt.3: CR Maintenance” appears.

• Press the [Enter] key.

[5]

Press the [Enter] key.

• The carriage moves to the center of the printer.

• The cleaning wiper moves upward.

The message on the left will appear.

[6]

Hold the tab on the maintenance cover as shown on the left to gently
open the cover.

• Fully open the maintenance cover.

CAUTION

Set Media

Remove Media

Media Set

Low speed

Press!

Menu 3 :

Maintenance >

Mnt. 3 :

CR Maintenance

CR Maint. :

Start

CR Maint. :

End

Содержание VJ-626UF

















































































































































Результаты поиска

Содержание VJ-626UF

Отзывы:

Похожие инструкции для VJ-626UF

Бренды по названию

Популярные бренды

MUTOH VJ-626UF, Руководство по эксплуатации

Результаты поиска

Содержание VJ-626UF

Отзывы:

Похожие инструкции для VJ-626UF

Бренды по названию

Популярные бренды