MUTOH VJ-626UF Скачать руководство пользователя

Страница: 27 / 144

Turning the power ON 27

Powering ON/OFF

Turning the power ON

[1]

Close the front cover.

[2]

Press the power button to turn the power ON.

• The blue light turns on.

• This printer starts its initialization operations.

Note

• During printer initialization, the printer performs table height calibration to optimize the gap between the print head and media.

• The table height calibration can be also performed from the operation panel “Mnt. 6: Calibration” menu.

"Calibrating table height" on page 53

Turning the power OFF

Important!

Use the printer with its power turned permanently on. When you are not using the printer, always leave the power on and put the

printer into the sleep mode while not in use.

If you do not put the printer into the sleep mode, the ink inside the printer could settle out and/or coagulate, causing poor image

quality or printer failure.

"Sleep Mode" on page 29

[1]

Check that the printer completes printing and no object including a jig is loaded on the table.

[2]

Prepare items required for daily maintenance.

"Preparing for Daily Maintenance" on page 100

[3]

Press the power button to turn the power OFF.

[4]

Press the [Enter] key.

Powering ON/OFF

Option

Media Set

Press!

Option

Media Set

Press!

Daily Maint. :

Start

Содержание VJ-626UF

















































































































































Результаты поиска

Содержание VJ-626UF

Отзывы:

Похожие инструкции для VJ-626UF

Бренды по названию

Популярные бренды

MUTOH VJ-626UF, Руководство по эксплуатации

Результаты поиска

Содержание VJ-626UF

Отзывы:

Похожие инструкции для VJ-626UF

Бренды по названию

Популярные бренды