MUTOH VJ-626UF Скачать руководство пользователя

Страница: 30 / 144

30 Turning the power OFF

[7]

Press the [Enter] key.

[8]

The message on the left will appear.

• Remove the media and the jig on the table, and then press the

[Enter] key.

The table, carriage and cleaning wiper move to gain access to daily
maintenance.

[9]

The message on the left will appear.

• You can start daily maintenance.

"Performing Daily Maintenance" on page 102

• After the daily maintenance is complete, press the [Enter] key.

The printer automatically performs the “Short” cleaning.

The sleep mode will start.

• To exit the sleep mode, press the [Enter] key.

Note

• The power button flashes in blue while the printer is in the sleep mode.

• To set the timer for automatic head cleaning during sleep mode, see

"SleepMode 2: SetTimer" on page 88

• Depending on the elapsed time from the previous automatic maintenance, the printer may automatically execute head cleaning and/or

ink charging, etc., when it exits the sleep mode. Such operation does not depend on the sleep mode settings. It is an automatic
maintenance function of the printer.

Daily Maint. :

Start

Remove Media

- >

Wait for a while

Daily Maint. :

End

Cleaning

Restart

Enter

Содержание VJ-626UF

















































































































































Результаты поиска

Содержание VJ-626UF

Отзывы:

Похожие инструкции для VJ-626UF

Бренды по названию

Популярные бренды

MUTOH VJ-626UF, Руководство по эксплуатации

Результаты поиска

Содержание VJ-626UF

Отзывы:

Похожие инструкции для VJ-626UF

Бренды по названию

Популярные бренды