MUTOH VJ-626UF Скачать руководство пользователя

Страница: 88 / 144

88 Option 1: Rotary Unit

Menu5: Option

Menu6: Sleep Mode

Option 1: Rotary Unit

Use this menu to attach the Rotary Unit (option).
For more details of this menu, see the Rotary Unit Operation Manual.

Note

If the printer starts switching to Rotary Mode due to wrong key operation, you can cancel it by pressing the Cancel key while the following

message is displayed on the operation panel.

• “Remove Media ->Enter”

• “Install Rotary Unit -> E”

SleepMode 1: Start

Activate Sleep Mode. Make sure to follow the instructions on the operation
panel to perform daily maintenance.

"Sleep Mode" on page 29

SleepMode 2: SetTimer

Sets the timer to perform head cleaning in the sleep mode.

Setting values

<Off> / 1 / 2 / 3 / 4 / 5 / 6 / 9 / 12 / 18 /
24 hours
<> indicates the default setting.
If you set an interval, the display will shift
to “SleepMode 1: Start”.

Important!

In following cases, the printer does not perform head cleaning by the timer in sleep mode.

• Front cover is open.

• Maintenance cover is open.

• The waste ink tank is full.

• There is little remaining ink in the ink cartridge (or no ink).

• The ink cartridge has been removed.

• The inserted ink cartridge is not the genuine ink cartridge, etc.

If one of the above conditions occurs during Head cleaning, cleaning is stopped.

When the printer returns to a normal state, Head cleaning is restarted.

Menu 5: Option

Option 1 :

Rotary Unit

Menu 6: Sleep Mode

SleepMode 1 :

Start

SleepMode 2 :

SetTimer

CleaningTimer :

Off

Содержание VJ-626UF

















































































































































Результаты поиска

Содержание VJ-626UF

Отзывы:

Похожие инструкции для VJ-626UF

Бренды по названию

Популярные бренды

MUTOH VJ-626UF, Руководство по эксплуатации

Результаты поиска

Содержание VJ-626UF

Отзывы:

Похожие инструкции для VJ-626UF

Бренды по названию

Популярные бренды