MUTOH VJ-626UF Скачать руководство пользователя

Страница: 104 / 144

104 Performing Daily Maintenance

Cleaning of print head circumference

[1]

Look in the tray to check the bottom of the carriage.
Check if dusts and ink deposit are adhered.

• Print head circumference (silver metal part)

• Print head guide part (black plastic part)

Important!

If maintenance cleaner is splashed onto the printer, use a paper towel to

wipe it off.

[2]

Use the cleaning stick to remove the ink and dust on the circumference of the bottom of the carriage.

[3]

Remove the tray from the table, and then close the front cover gently.

[4]

Next clean the cleaning wiper and the cap circumference.

Print head circumference

Print head guide part

DO NOT touch the surface of a print head (the yellow portions in the illustration below)

Cleaning required

Print head circumference (silver metal part)

Print head guide part (black plastic part)

Содержание VJ-626UF

















































































































































Результаты поиска

Содержание VJ-626UF

Отзывы:

Похожие инструкции для VJ-626UF

Бренды по названию

Популярные бренды

MUTOH VJ-626UF, Руководство по эксплуатации

Результаты поиска

Содержание VJ-626UF

Отзывы:

Похожие инструкции для VJ-626UF

Бренды по названию

Популярные бренды