MUTOH VJ-626UF Скачать руководство пользователя

Страница: 132 / 144

132 Error message display and possible solutions

[******] Check Ink

Ink cartridges were not recognized correctly.
Insert ink cartridges correctly again.
Contact your local MUTOH dealer.

[*] Reseat Ink

Because the Smart chip card is poor in contact, the reinsertion of the ink
cartridge is necessary.
Reseat all the ink cartridges.

Daily Maint. Error

An obstacle has been detected. Press any key on the operation panel.
Remove any object including a jig from the table and then perform daily
maintenance.

Obstacle detected
Press Remove Media
Key.

An obstacle has been detected. Press the [Remove Media] key, and reset the
media in place.

"Loading media" on page 32

Table Height Error
Press Remove Media
Key.

The printer cannot lower the table any further as specified by RIP software,
and will cancel the printing.

Obst. - > Print Cancel

An obstacle has been detected.
Press the [Enter] key to cancel the job.

Obst. - > PrintContinue

An obstacle has been detected.
Press the [Enter] key to resume the job without changing the table height.

Err! Reboot Printer

Activation has failed. Restart the printer and activate the printer again.

Life Times [Pump]

The operational life of the pump motor has almost expired.
(Continues operation)
Contact your local MUTOH dealer.

Life Times [CR Motor]

The operation life CR motor has almost expired.
(Continues operation)
Contact your local MUTOH dealer.

Life Times [PF Motor]

The operational life of the PF motor has almost expired.
(Continues operation)
Contact your local MUTOH dealer.

Life Times [PG Motor]

The operational life of the PG motor has almost expired.
(Continues operation)
Contact your local MUTOH dealer.

Life Times [C Pump]

The operational life of Circulation pump motor is almost expired.
(Continues operation)
Contact your local MUTOH dealer.

Life Times [UV Lamp]

The operational life of UV LED has almost expired.
(The operation continues.)
Contact your local MUTOH dealer.

Shake W Cartridge

Agitate the White (Wh) ink cartridge.

Shake KMCY Cartridge

Agitate the Black (K), Magenta (M), Cyan (C), and Yellow (Y) ink cartridges.

Shake KMCYW Cartridge

Agitate the Black (K), Magenta (M), Cyan (C), Yellow (Y), and White (Wh) ink
cartridges.

Shake ALL Cartridge

Agitate all ink cartridges.
Agitate the Black (K), Magenta (M), Cyan (C), and Yellow (Y) ink cartridges.

Display

Description

Содержание VJ-626UF

















































































































































Результаты поиска

Содержание VJ-626UF

Отзывы:

Похожие инструкции для VJ-626UF

Бренды по названию

Популярные бренды

MUTOH VJ-626UF, Руководство по эксплуатации

Результаты поиска

Содержание VJ-626UF

Отзывы:

Похожие инструкции для VJ-626UF

Бренды по названию

Популярные бренды