MUTOH VJ-626UF Скачать руководство пользователя

Страница: 32 / 144

32 Loading media

Loading media

•

Do not open or close the cover while you are off balance.

You may pinch your finger or get injured.

• Hold the handle of the front cover and gently open or close the cover.

If excessive force is applied to the cover, it will shorten its life or will damage to the printer.

Important!

When loading a new media, make sure to place it on an appropriate position and input correct media information.

If wrong information is entered, the printer can print on an unintended position of the table. Once UV ink stains on the table, it will

be cured by UV lamp and will not be removed from the table.

Placing the media on the table

[1]

Check that the message on the left is displayed.

• If not displayed, press the [Remove Media] key.

[2]

Hold the handle on the front cover to gently open it.

• Fully open the front cover.

Check that the message on the left is displayed.

Note

• If the message on the left is displayed, you can use the [+] and [ - ] keys to

change the vacuum fan setting.
Change this setting depending on the thickness of the media.

• The vacuum fan will start operating when the [+] or [ -] key is pressed.

• If you change the setting, it will be reflected in the currently selected User

Type.

[3]

Place the media on the table.

CAUTION

Set Media, then

press Set Media key.

Set media, then

+ -

close

cover.

Содержание VJ-626UF

















































































































































Результаты поиска

Содержание VJ-626UF

Отзывы:

Похожие инструкции для VJ-626UF

Бренды по названию

Популярные бренды

MUTOH VJ-626UF, Руководство по эксплуатации

Результаты поиска

Содержание VJ-626UF

Отзывы:

Похожие инструкции для VJ-626UF

Бренды по названию

Популярные бренды