MUTOH VJ-626UF Скачать руководство пользователя

Страница: 83 / 144

Mnt. 3: CR Maintenance 83

Mnt. 3: CR Maintenance

Use this for replacing absorption material for the flushing box and cleaning
wiper.

"Replacing absorption material for the flushing box" on page 116
"Replacing the cleaning wiper" on page 119

Submenus

Press the [Enter] key to replace the
absorption material for the flushing box.

• The carriage moves to the center of the

printer.

• The cleaning wiper moves upward.

After the replacement is complete, press
the [Enter] key.

• The printer moves the carriage and the

cleaning wiper back to each original
position.

Mnt. 4: UV Scan

Performs further UV curing.
Use this when you want to promote ink curing by applying additional UV light.

Submenus

"UV Scan 1: Start" on page 84

"UV Scan 2: Scans" on page 84

"UV Scan 3: Post Cure" on page 84

Note

The range over which the UV scanning is executed will depend on the current settings for “Size” and “Location” in the “MediaSetting” User

Type.

Mnt. 3 :

CR Maintenance

CR Maint. :

Start

CR Maint. :

End

Mnt. 4 :

UV Scan >

UV Scan1 :

Start

UV Scan2 :

Scans

UV Scan3 :

Post Cure

Содержание VJ-626UF

















































































































































Результаты поиска

Содержание VJ-626UF

Отзывы:

Похожие инструкции для VJ-626UF

Бренды по названию

Популярные бренды

MUTOH VJ-626UF, Руководство по эксплуатации

Результаты поиска

Содержание VJ-626UF

Отзывы:

Похожие инструкции для VJ-626UF

Бренды по названию

Популярные бренды