MUTOH VJ-626UF Скачать руководство пользователя | Manualshive

Страница: 116 / 144

background image

116 Replacing absorption material for the flushing box

3

Replacing consumable parts

The flushing box is a part that keeps receiving ink discharged from the print head. Please replace the absorption material for the
flushing box periodically. If used without replacing, it can cause damage to the print head.

Replacing period:

• Approx. every two months (since it differs depending on usage frequency, please check periodically)

Replacing absorption material for the flushing box

Skin or eye contact with UV curable ink may cause skin inflammation or allergic reaction.

For this operation, be sure to wear the supplied gloves (or solvent resistant gloves) and goggles to prevent ink from contacting
with your eyes or skin.

Do not open or close the cover while you are off balance.

You may pinch your finger or get injured.

1.

Checking steps

[1]

Hold the tab on the maintenance cover as shown on the left to gently
open the cover.

• Fully open the maintenance cover.

Always fully open the maintenance cover.

If you leave it half-open, the maintenance cover can suddenly close.

[2]

• Check the absorption material for the flushing box.

• If the ink deposit is visible on the flushing box, replace the

absorption material.

Replacing consumable parts

CAUTION

CAUTION

Time to replace

«
...
114
115
116
117
118
...
»

Содержание VJ-626UF

















































































































































Отзывы:

Нет отзывов

Похожие инструкции для VJ-626UF

Бренд: Xerox Страницы: 414

Бренд: Olympus Страницы: 2

Бренд: Olympus Страницы: 148

Бренд: Oki Страницы: 24

Бренд: Oki Страницы: 126

Бренд: Partner Страницы: 34

Бренд: Partner Страницы: 81

Бренд: Xerox Страницы: 288

Бренд: Sindoh Страницы: 33

Falcon Outdoor 46

Бренд: MUTOH Страницы: 333

Accel-a-Writer 8200

Бренд: Xante Страницы: 12

8860MFPD - Multifunction Inkjet Printer

Бренд: Xerox Страницы: 16

Бренд: WOOSIM Страницы: 67

Бренд: Triumph Adler Страницы: 59

Бренд: Canon Страницы: 2

PIXMA MP230 Series

Бренд: Canon Страницы: 4

Бренд: Canon Страницы: 4

Бренд: Canon Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды