MUTOH VJ-626UF Скачать руководство пользователя | Manualshive

Страница: 107 / 144

background image

Head cleaning 107

3

Printer Maintenance

When nozzle clogging is found in nozzle check, perform head cleaning. Head cleaning consumes ink.
There are several cleaning modes in this printer. Please select an appropriate mode based on your usage condition.

Important!

Comply strictly with the following when you performing “Little Charge” or “Initial Charge”. If charging is interrupted, ink will be

lost when charging is resumed.

• Do not open the Front cover or the Maintenance cover.

• Do not use ink cartridges that have little ink remaining.

Head cleaning

Short cleaning

Consumes less ink than Normal cleaning.

Normal cleaning

Perform nozzle check before and after printing, and use when nozzle clogging is found on
the nozzle check print.

Long cleaning

Consumes more ink than Normal cleaning. When nozzle clogging still occurs after Normal
cleaning, perform Long cleaning.

Little Charge

Provides higher cleaning effect than Long cleaning, it consumes a large amount of ink.
*This mode cannot be selected via the “Cleaning” key. Select it from the Cleaning submenu
in the Panel Setting Menus.

"Mnt. 1: Cleaning" on page 82

Initial Charge

Provides higher cleaning effect than “LittleCharge”, but also consumes rather more ink.
*This mode cannot be selected via the “Cleaning” key. Select it from the Cleaning submenu
in the Panel Setting Menus.

"Mnt. 1: Cleaning" on page 82

Steps for head cleaning

[1]

Use the [Cleaning] key to select a cleaning mode.

• The “Cleaning Mode” indicators will change each time the key is

pressed.

Note

• You can alternatively do this via the printer driver or the VSM’s

remote panel.

• The “Cleaning Mode” indicators will change as shown below.

Printer Maintenance

Option

1

2

Set Media

Remove Media

Media Set

Low speed

Press!

Short Cleaning

Normal Cleaning

Long Cleaning

«
...
105
106
107
108
109
...
»

Содержание VJ-626UF

















































































































































Отзывы:

Нет отзывов

Похожие инструкции для VJ-626UF

Бренд: WANHAO Страницы: 29

ZINK PANPRINT01

Бренд: Pandigital Страницы: 2

DiMAGE Scan Elite 5400 II

Бренд: Konica Minolta Страницы: 38

Бренд: Afinia 3D Страницы: 47

Бренд: BART-TECH 3D Страницы: 34

Бренд: VuPoint Страницы: 20

Бренд: Stratasys Страницы: 68

Бренд: Star Micronics Страницы: 130

Бренд: OKIDATA Страницы: 39

Бренд: Aficio Страницы: 92

Бренд: Oki Страницы: 309

Dynacode II IP107

Бренд: Carl Valentin Страницы: 168

Бренд: Canon Страницы: 327

ViperTX Extreme

Бренд: MUTOH Страницы: 132

Viper TX Softsign

Бренд: MUTOH Страницы: 196

imageClass LBP6030

Бренд: Canon Страницы: 272

KX-P1131 - KX-P 1131 B/W Dot-matrix Printer

Бренд: Panasonic Страницы: 6

KX-MC6000 Series

Бренд: Panasonic Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды