MUTOH VJ-626UF Скачать руководство пользователя

Страница: 45 / 144

What you can do on the operation panel during printing 45

With this menu, you can alter the micro-adjustment value for the feed correction. The alteration will be valid for the current

printing only.

• See the following related sections of Panel Setting Menus (Chapter 2 below):

"**>3: PF Adjust" on page 63

With this menu, you can have a change that you made via “Menu1: PF Micro Adj.” reflected in the currently selected User Types.

Menu1: PF Micro Adjustment

[1]

Press the [Enter] key to access the menu.

[2]

• Use the [+] / [ - ] key to change the setting value.

• Press the [Enter] key to set the changed value.

Note

• The changed value set with this menu will become invalid when the

printing ends.

• To have the change reflected in the currently selected User Type, save it

using “Menu2: Backup”.

Menu2: Backup

[1]

Press the [Enter] key.

[2]

Press the [Enter] key.

The setting value will be saved.

Menu1 :

PF Micro Adj.

Micro

5.00

Menu2:

Backup

Update Parameter

？

* Parameter Updating *

Содержание VJ-626UF

















































































































































Результаты поиска

Содержание VJ-626UF

Отзывы:

Похожие инструкции для VJ-626UF

Бренды по названию

Популярные бренды

MUTOH VJ-626UF, Руководство по эксплуатации

Результаты поиска

Содержание VJ-626UF

Отзывы:

Похожие инструкции для VJ-626UF

Бренды по названию

Популярные бренды