MUTOH VJ-626UF Скачать руководство пользователя

Страница: 62 / 144

62 Set 1: User Type

Confirm pattern

• Press the [Enter] key to carry out printing.

• Check the pattern print. If there are misalignments, proceed to rough adjustment pattern printing.

• In the picture below, there are misalignments.

Rough adjustment pattern

• Press the [Enter] key to carry out printing.

• Look for and mark a number printed under a pattern that has least misalignment.

• “Pattern B: 6” or similar will appear in the display. Use the [+] / [ - ] key to enter in the display the number that you marked,

and press the [Enter] key.

• In the case of the picture below, enter “7”, so that the display reads “Pattern B: 7”.

Fine adjustment pattern

• Press the [Enter] key to carry out printing.

• Look for and mark a number printed under a pattern that has least misalignment.

• “Pattern B: 4” or similar will appear in the display. Use the [+] / [ - ] key to enter in the display the number that you marked,

and press the [Enter] key.

• In the case of the picture below, enter “6”, so that the display reads “Pattern B: 6”.

Pattern name

Printing
settings

Bi-dir
normal speed
medium drop family

Good

Not Good

Bi-dir
normal speed
medium drop family

Содержание VJ-626UF

















































































































































Результаты поиска

Содержание VJ-626UF

Отзывы:

Похожие инструкции для VJ-626UF

Бренды по названию

Популярные бренды

MUTOH VJ-626UF, Руководство по эксплуатации

Результаты поиска

Содержание VJ-626UF

Отзывы:

Похожие инструкции для VJ-626UF

Бренды по названию

Популярные бренды