MUTOH VJ-626UF Скачать руководство пользователя

Страница: 102 / 144

102 Performing Daily Maintenance

Performing Daily Maintenance

Cleaning of UV Lamp

[1]

Open the front cover gently, and then place the tray on the table.

Important!

Do not place any object inside the printer.

[2]

Look in the stainless tray to check for ink or dust on the UV lamp.

• If no ink or dust is found on the UV lamp, skip this step and move on to

"Moistening the surface of print head nozzles"

on page 103

[3]

If any ink or dust is found, using a paper towel, remove ink and dust from the UV lamp.

• If ink deposits cannot be removed with the paper towel, use the scraper supplied with the printer.

• Press the scraper on the ink deposits with a slight angle and scrape off the ink deposits.

• Use the paper towel to clean the ink scraped from the lamp.

Important!

• Make sure to use the scraper supplied with the printer.

• Never use the corner of the scraper. It can damage the UV lamp.

• When using the scraper, do not apply too much pressure to the lamp. It can damage the UV lamp.

[4]

Next moisten the surface of print head nozzles.

Scraper

Содержание VJ-626UF

















































































































































Результаты поиска

Содержание VJ-626UF

Отзывы:

Похожие инструкции для VJ-626UF

Бренды по названию

Популярные бренды

MUTOH VJ-626UF, Руководство по эксплуатации

Результаты поиска

Содержание VJ-626UF

Отзывы:

Похожие инструкции для VJ-626UF

Бренды по названию

Популярные бренды