MUTOH VJ-626UF Скачать руководство пользователя | Manualshive

Страница: 96 / 144

background image

96 Emptying waste ink tank

3

Emptying waste ink tank

When a certain amount of waste fluid has been collected in the waste ink tank, the error LED on the operation panel of this
printer turns on with beep sounds.
Drain all waste fluid in the waste ink tank into a container (e.g. PET bottle). After emptying the waste ink tank, reset the waste
ink counter.

Display messages

Emptying waste ink tank

The waste ink tank is about to become full. Mutoh recommends that
you empty the waste ink tank before it is completely full.

• Printing or other operation will continue while you do this.

The waste ink tank has become full. Empty the waste ink tank
immediately.

• Printing or other operation will stop. It will resume when you have

carried out “ResetWasteInk”.

Do not mix waste fluid with any other chemicals, even in a small amount.

If mixed with other chemicals (e.g. oxidizing agent), it may produce heat.
Before pouring waste fluid into a container, make sure:

• the container is empty.

• inside the container is completely dry.

Skin or eye contact with UV curable ink may cause skin inflammation or allergic reaction.

For this operation, be sure to wear the supplied gloves (or solvent resistant gloves) and goggles to prevent ink from contacting
with your eyes or skin.

Important!

Empty the waste ink tank before moving the printer.

If ink splashes inside the waste ink tank while being moved, it can cause damage.

Emptying waste ink tank

NearFullWasteInkTank

Full WasteInkTank

WARNING

CAUTION

«
...
94
95
96
97
98
...
»

Содержание VJ-626UF

















































































































































Отзывы:

Нет отзывов

Похожие инструкции для VJ-626UF

Бренд: Oki Страницы: 24

Бренд: VAF instruments Страницы: 24

Бренд: 3DP Страницы: 12

Бренд: Oki Страницы: 40

Бренд: Lanier Страницы: 265

Бренд: Canon Страницы: 21

Бренд: Olivetti Страницы: 22

FELIX Pro 3 Touch

Бренд: Felix printers Страницы: 29

Бренд: Citizen Страницы: 3

Бренд: Flashforge Страницы: 44

Бренд: RAYSHAPE Страницы: 41

Accel-a-Writer 4

Бренд: Xante Страницы: 12

Бренд: Epson Страницы: 105

Бренд: Epson Страницы: 128

Бренд: Epson Страницы: 145

Бренд: Epson Страницы: 200

Бренд: Epson Страницы: 2

Бренд: Fujitsu Страницы: 264

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды