MUTOH VJ-626UF Скачать руководство пользователя

Страница: 37 / 144

Nozzle check and cleaning 37

Before starting everyday operation, please perform nozzle check printing to check the print head condition. If nozzle clog is

found, perform cleaning.

This printer offers the following two kinds of nozzle checks:

• Nozzle Check - Prints the nozzle check patterns.

• Nozzle Check B - Prints the nozzle check patterns on the partially colored background.

Nozzle check and cleaning

Note

• “Nozzle Check B” will only appear in the menu if the printer is set to 6-color configuration.

• When using white ink, colored media, transparent films or semi-transparent films (such as OHP film, tracing paper and more) are

recommended to use for nozzle check.

Important!

Before loading media, read

"Cautions for handling media" on page 24

and then load it on the table.

•

Do not open or close the cover while you are off balance.

You may pinch your finger or get injured.

• Hold the handle of the front cover and gently open or close the cover.

If excessive force is applied to the cover, it will shorten its life or will damage to the printer.

Nozzle check steps

[1]

Check that the message on the left is displayed.

• If not displayed, press the [Remove Media] key.

[2]

Hold the handle on the front cover to gently open it.

• Fully open the front cover.

CAUTION

Set Media, then

press Set Media key.

Содержание VJ-626UF

















































































































































Результаты поиска

Содержание VJ-626UF

Отзывы:

Похожие инструкции для VJ-626UF

Бренды по названию

Популярные бренды

MUTOH VJ-626UF, Руководство по эксплуатации

Результаты поиска

Содержание VJ-626UF

Отзывы:

Похожие инструкции для VJ-626UF

Бренды по названию

Популярные бренды