MOTO GUZZI Stelvio 1200 MY11 2011 Скачать руководство пользователя страница 264

Страница: 264 / 385

Specification

Desc./Quantity

Target engine revs

1150 rpm (approximate values)

Parameter valid at idle, setting depends especially on the en-

gine temperature: the control unit will try to keep the engine

running at this revs, acting on the ignition advance and the

Stepper motor

Stepper base

70 - 100 (approximate values)

Steps corresponding to the Stepper motor reference position

CL Stepper

70 - 150 (approximate values)

Steps set by the control unit for the Stepper motor. At idle, steps
so that the engine keeps the target engine revs set by the con-

trol unit

Stepper regulator

Difference between current steps of motor at idle and those at

the reference position

Virtual throttle angle from Stepper

0°

With engine not at idle speed, this value indicates the throttle

degrees corresponding to the Stepper motor air flow

STATUS screen page

This screen page shows the status (usually ON/

OFF) of the vehicle devices or the operation con-

dition of some vehicle systems (for example, lamb-

da probe functioning status).

STATUSES

Specification

Desc./Quantity

Engine status

ON/run/power-latch/stopped

operation conditions

Throttle position

Released / pressed

indicates if the throttle potentiometer is open or closed

Stand

Retracted / extended

indicates the position of the side stand (only with gear engaged)

Ignition

Enabled / disabled

indicates if the control unit consents engine start-up

RUN / STOP switch

Run / stop

indicates the position of the safety switch

Clutch

No / Yes

indicates the clutch sensor status

Gear engaged

No / Yes

indicates the gear sensor status

fall sensor

Normal / Tip over

indicates the vehicle fall sensor status

Lambda

Open loop / Closed loop

Indicates if the control unit is using (CLOSED) the lambda

probe signal to keep the stoichiometric combustion. At idle

CLOSED only if: Air T over 20°C (68°F) and engine T over 30°

C (86°F) and engine on for at least 2-3 minutes

Synchronisation

Synchronised / Not synchronised

Indicates if the control unit detects the revolution sensor signal

correctly

Power supply

Stelvio 1200 NTX MY11

P SUPP - 264

Содержание Stelvio 1200 MY11 2011


































































































































































































































































































































































































Результаты поиска

Содержание Stelvio 1200 MY11 2011

Отзывы:

Похожие инструкции для Stelvio 1200 MY11 2011

Бренды по названию

Популярные бренды

MOTO GUZZI Stelvio 1200 MY11 2011, Руководство по обслуживанию станции

Результаты поиска

Содержание Stelvio 1200 MY11 2011

Отзывы:

Похожие инструкции для Stelvio 1200 MY11 2011

Бренды по названию

Популярные бренды