MOTO GUZZI Stelvio 1200 MY11 2011 Скачать руководство пользователя страница 69

Страница: 69 / 385

•

Remove the air filter.

•

Plug the intake duct with a clean cloth to prevent any foreign objects from entering the intake

manifold.

DO NOT START THE ENGINE WITHOUT THE AIR FILTER.
TO CLEAN THE FILTERING ELEMENT, USE A PRESSURE AIR JET FROM THE INSIDE TO THE
OUTSIDE.

Checking the valve clearance

If the timing system is very noisy, check the clearance between the valves and the rocking levers.

NOTE

ADJUST WITH COLD ENGINE, WITH PISTON AT TOP DEAD CENTRE (TDC) IN COMPRESSION
STROKE (VALVES CLOSED).

•

Disconnect the spark plug by leverag-

ing a screwdriver through the slot.

CAUTION

PAY ATTENTION TO APPLY LEVERAGE ON THE RUBBER
OF THE SPARK PLUG CAP ITSELF IN ORDER TO AVOID
DAMAGES

•

Unscrew and remove the four head

cover fixing screws and collect the

sealing O-rings.

•

Remove the head cover together with

the gasket.

•

Loosen the nut (1).

•

Use a screwdriver to act on set screw

(2) until the following clearances are

obtained:

Technical specifications

Values valid with control clearance between

rockers and valve

Inlet valve: 0.15 mm (0.0059 in)

Exhaust valve: 0.20 mm (0.0079 in)

Stelvio 1200 NTX MY11

Maintenance

MAIN - 69

Содержание Stelvio 1200 MY11 2011


































































































































































































































































































































































































Результаты поиска

Содержание Stelvio 1200 MY11 2011

Отзывы:

Похожие инструкции для Stelvio 1200 MY11 2011

Бренды по названию

Популярные бренды

MOTO GUZZI Stelvio 1200 MY11 2011, Руководство по обслуживанию станции

Результаты поиска

Содержание Stelvio 1200 MY11 2011

Отзывы:

Похожие инструкции для Stelvio 1200 MY11 2011

Бренды по названию

Популярные бренды