MOTO GUZZI Stelvio 1200 MY11 2011 Скачать руководство пользователя страница 232

Страница: 232 / 385

Disassembling the connecting rod

•

Remove both heads.

•

Remove the cylinders and the pistons.

•

Remove the oil sump.

•

Undo the coupling screws (A) inside

the crankcase and remove the con-

necting rods (B).

See also

Removing the flywheel
Disassembling the piston
Removing the

cylinder

Removing the

cylinder head

Inspecting the crankshaft components

Check the surfaces of the main journals; if they are

scored or oval-shaped, reface them (observing the

undersize charts), and replace the main bushing/

Reference (1) indicates the position where the col-

oured reference is applied to select diameter (B).

Reference (2) indicates the position where the col-

oured reference is applied to select balancing.

CRANKSHAFT SEAT (TIMING SYSTEM SIDE)

Specification

Desc./Quantity

Diameter of crankshaft main journal, timing system side

37.975 - 37.959 mm (1.49507 - 1.49444 in)

Inside diameter of crankshaft bushing, timing system side

38.016 - 38.0 mm (1.49669 - 1.49606 in)

Clearance between bushing and main journal (timing system

side)

0.025 - 0.057 mm (0.00098 - 0.00224 in)

CRANKSHAFT SEAT ( CLUTCH SIDE)

Specification

Desc./Quantity

Diameter of crankshaft main journal, clutch side

53.97 - 53.961 mm (2.12480 - 2.12444 in)

Inside diameter of crankshaft bushing on clutch-side flange

54.019 - 54.0 mm (2.12673 - 2.12598 in)

Clearance between bushing and main journal (clutch side)

0.030 - 0.058 mm (0.00118 - 0.00228 in)

CRANKPIN DIAMETER (B)

Specification

Desc./Quantity

'Blue' bushing half-shell regular production

44.008 ÷ 44.014 mm (1.73259 ÷ 1.73283 in)

'Red' bushing half-shell regular production

44.014 ÷ 44.020 mm (1.73283 ÷ 1.73307 in)

Engine

Stelvio 1200 NTX MY11

ENG - 232

Содержание Stelvio 1200 MY11 2011


































































































































































































































































































































































































Результаты поиска

Содержание Stelvio 1200 MY11 2011

Отзывы:

MOTO GUZZI Stelvio 1200 MY11 2011, Руководство по обслуживанию станции, Страница: 232 / 385

Результаты поиска

Содержание Stelvio 1200 MY11 2011

Отзывы: