MOTO GUZZI Stelvio 1200 MY11 2011 Скачать руководство пользователя страница 200

Страница: 200 / 385

•

Use a reamer to bore the holes the valve stems slide through so that the inside diameter is

at the prescribed value. The interference between the seat on the head and the valve guide

must be 0.046 - 0.075 mm (0.0018 - 0.0030 in)

VALVE GUIDE COUPLING - VALVES (INLET)

Specification

Desc./Quantity

Valve guide inside diameter

5.0 - 5.012 mm (0.19685 - 0.19732 in)

Valve stem diameter

4.972 - 4.987 mm (0.19574 - 0.19633 in)

Fitting clearance

0.013 - 0.040 mm (0.00051 - 0.00157 in)

VALVE GUIDE COUPLING - VALVES (OUTLET)

Specification

Desc./Quantity

Valve guide inside diameter

5.0 - 5.012 mm (0.19685 - 0.19732 in)

Valve stem diameter

4.960 - 4.975 mm (0.19527 - 0.19587 in)

Fitting clearance

0.025 - 0.052 mm (0.00098 - 0.00205 in)

Checking the cylinder head

Check that:

•

The planes of contact with the cover and with the cylinder are not scored or damaged so as

to compromise a perfect seal.

•

Check that the clearance between the valve guide holes and valve stanchions is within the

prescribed limits.

•

Check the status of the valve seats.

INLET VALVE SEAT DETAIL DRAWING

OUTLET VALVE SEAT DETAIL DRAWING

- If the width of the mark on the valve seat is larger than the prescribed limits, true the seats with a 45°

milling cutter and then grind.

Engine

Stelvio 1200 NTX MY11

ENG - 200

Содержание Stelvio 1200 MY11 2011


































































































































































































































































































































































































Результаты поиска

Содержание Stelvio 1200 MY11 2011

Отзывы:

MOTO GUZZI Stelvio 1200 MY11 2011, Руководство по обслуживанию станции, Страница: 200 / 385

Результаты поиска

Содержание Stelvio 1200 MY11 2011

Отзывы: