MOTO GUZZI Stelvio 1200 MY11 2011 Скачать руководство пользователя страница 103

Страница: 103 / 385

Battery

12 V - 18 Ampere/hour

Speed sensor

FRONT

FUNCTION:

To indicate the vehicle speed by read-

ing the front wheel turning speed.

OPERATION / OPERATING PRINCIPLE:

Magne-

toresistive sensor: a square-wave pulse is gener-

ated with voltage approx. between 11.55 V and

11.25 V

WIRING DIAGRAM

Level in wiring diagram: ABS.

REMOVAL

LOCATION ON THE VEHICLE:

on the fork, right

stem, next to the brake calliper support.

CONNECTOR LOCATION (if available):

under

the fuel tank, front position.

PINS

•

PIN 1- Ground connection (white)

•

PIN 2 - Power supply voltage/Output

signal (white/brown)

NAVIGATOR: PARAMETERS

Speed sensor

Vehicle speed: km/h

FRONT SPEED SENSOR,

ELECTRICAL ERRORS

5D90 electric malfunction:

Electrical fault in sensor or cable harness.

Troubleshooting:

Check the sensor connector and the ABS control unit connector. If it is not OK,

restore the connectors; if it is OK, check continuity of the cable between sensor PIN 2 on the cable

harness side and PIN 14 ABS control unit connector. If there is no continuity, restore them. If there is,

Stelvio 1200 NTX MY11

Electrical system

ELE SYS - 103

Содержание Stelvio 1200 MY11 2011


































































































































































































































































































































































































Результаты поиска

Содержание Stelvio 1200 MY11 2011

Отзывы:

MOTO GUZZI Stelvio 1200 MY11 2011, Руководство по обслуживанию станции, Страница: 103 / 385

Результаты поиска

Содержание Stelvio 1200 MY11 2011

Отзывы: