MOTO GUZZI Stelvio 1200 MY11 2011 Скачать руководство пользователя страница 233

Страница: 233 / 385

BALANCING SELECTION COLOURS (2)

Specification

Desc./Quantity

Crankshaft selection colour (2) brown

Type 1 to be used with brown connecting rods.

Balance with a

1558 g (54.96 oz) +/- 0.25%

weight fitted on the

crankpin (B). Maximum imbalance allowed for each shoulder:

2 g (0.07 oz)

Crankshaft selection colour (2) green

Type 2 to be used with green connecting rods.

Balance with a

1575 g (55.56 oz) +/- 0.25%

weight fitted on the

crankpin (B). Maximum imbalance allowed for each shoulder:

2 g (0.07 oz)

Crankshaft selection colour (2) black

Type 2 to be used with black connecting rods.

Balance with a

1592 g (56.16 oz) +/- 0.25%

weight fitted on the

crankpin (B). Maximum imbalance allowed for each shoulder:

2 g (0.07 oz)

Checking the connecting rod

When examining the connecting rods, check that:

•

Bushing conditions and bushings-pins clearance;

•

Shaft parallelism;

•

Connecting rod bearings.

These are thin shell bearings, anti-friction alloy that does not allow for any adaptation; replace them

immediately if seizing or wear marks are found.

Upon replacing the bearings it may be necessary to ream the crankshaft pin.

Before reaming the crankpin, measure the pin diameter (B) comparing it with the maximum wear al-

lowed, as indicated in the figure; this defines what kind of undersizing the bearing should have and to

which diameter the pin (B) should be reamed.

Checking shaft parallelism

Check shafts for squaring before fitting them.

It is therefore necessary to check that the head holes and the rod small end are parallel and on the

same plane.

The maximum parallelism and plane error of the two head shafts and connecting rod small end should

be +/- 0.10 mm (0.00393 inch).

Stelvio 1200 NTX MY11

Engine

ENG - 233

Содержание Stelvio 1200 MY11 2011


































































































































































































































































































































































































Результаты поиска

Содержание Stelvio 1200 MY11 2011

Отзывы:

Похожие инструкции для Stelvio 1200 MY11 2011

Бренды по названию

Популярные бренды

MOTO GUZZI Stelvio 1200 MY11 2011, Руководство по обслуживанию станции

Результаты поиска

Содержание Stelvio 1200 MY11 2011

Отзывы:

Похожие инструкции для Stelvio 1200 MY11 2011

Бренды по названию

Популярные бренды