MOTO GUZZI Stelvio 1200 MY11 2011 Скачать руководство пользователя страница 109

Страница: 109 / 385

Throttle actuator position sensor P0120

Example value:

open circuit, shorted to positive / shorted to negative.

Error cause

•

If the circuit is open, shorted to positive: excessive voltage has been detected at PIN 3 of

connector A (BROWN).

•

If shorted to negative: voltage equal to zero has been detected.

Troubleshooting

•

Circuit is open, shorted to positive: check the injection control unit connector and the sensor

connector: if they are not OK, restore; if they are OK, check continuity between PIN 3 of

connector A (BROWN) and PIN C of the sensor (red cable): if there is not continuity, restore

the cable harness; if there is continuity, check continuity of the sensor between PIN A and

PIN C: if there is not continuity, replace the potentiometer; if there is continuity, check the

resistance. If resistance is over 2.5 kOhm, it means the red cable is shorted to positive and

the cable harness should be restored

•

shorted to negative: disconnect the sensor connector and check the ground insulation of the

red cable (from throttle sensor connector or control unit connector): if there is continuity to

ground, restore the cable harness; if it is ground insulated, the resistance between PIN A

and PIN C is below 1.3 kOhm; therefore, the throttle body should be replaced

NAVIGATOR: ADJUSTMENT

Throttle position autodetection

: It allows the control unit to detect the closed throttle position; just

press the Enter key.

Self-adjustable parameters reset

: Lambda probe self-adaptability parameters reset: operation to be

carried out after the throttle body is cleaned or in the case a new engine, a new lambda probe or a new

injector is fitted, or the correct operation of the injection system or the valves is restored.

NAVIGATOR: RESET PROCEDURE

Once the throttle body or the injection control unit is replaced, it is necessary to connect to the diagnosis

instrument selecting FUEL INJECTION and carry out the operation: Throttle position autodetection.

Stelvio 1200 NTX MY11

Electrical system

ELE SYS - 109

Содержание Stelvio 1200 MY11 2011


































































































































































































































































































































































































Результаты поиска

Содержание Stelvio 1200 MY11 2011

Отзывы:

MOTO GUZZI Stelvio 1200 MY11 2011, Руководство по обслуживанию станции, Страница: 109 / 385

Результаты поиска

Содержание Stelvio 1200 MY11 2011

Отзывы: