MOTO GUZZI Stelvio 1200 MY11 2011 Скачать руководство пользователя страница 243

Страница: 243 / 385

The oil pump is operated by the gear (10) which receives the motion directly from the crankshaft. The

gear (10) is mounted on the shaft (8), on which two rotors are fitted: one for engine cooling (7) and

another for lubrication (6).

Cooling:

The rotor (7) takes in oil from the sump through the filter (12); the oil is sent to the radiator (1) through

the hoses (3). Oil passes through the radiator (1) dispersing part of the heat and reaches the heads

through the hoses (2). Oil goes down to the sump again and joins the oil used for lubrication.

Lubrication:

The rotor (6) takes in oil from the sump through the filter (11); the oil is sent through special ducts in

the crankcase to all the parts to be lubricated. Oil goes down to the sump again and joins the oil used

for cooling.

Oil pump

Removing

•

Drain the engine oil.

•

Remove the generator and the timing

system cover.

•

Unscrew and remove the nipple.

•

Collect the gasket.

•

Remove the nipple - oil pump fitting.

Stelvio 1200 NTX MY11

Engine

ENG - 243

Содержание Stelvio 1200 MY11 2011


































































































































































































































































































































































































Результаты поиска

Содержание Stelvio 1200 MY11 2011

Отзывы:

MOTO GUZZI Stelvio 1200 MY11 2011, Руководство по обслуживанию станции, Страница: 243 / 385

Результаты поиска

Содержание Stelvio 1200 MY11 2011

Отзывы: