MOTO GUZZI Stelvio 1200 MY11 2011 Скачать руководство пользователя страница 113

Страница: 113 / 385

of the BROWN connector and PIN 2 of sensor: restore cable harness if there is not continuity;

if it is OK, reconnect the control unit connector and, with key set to key ON, check the

continuity between the sensor connector PIN 1 and the vehicle ground connection: if there

is not continuity, restore the cable harness; if there is continuity, it means that the cause of

the error is that the cable is shorted to positive and now the cable harness between the

BROWN PIN 14 and PIN 2 of the sensor should be restored. If the engine temperature

sensor error is displayed at the same time, this means that the grey cable common for both

sensors is shorted to positive.

•

If shorted to negative, check sensor correct resistance: if resistance = 0, replace the sensor;

if resistance is correct, it means that the pink/black cable has ground connection: restore

the cable harness

NOTES

No error is detected if the sensor does not work correctly or the control unit connector

or sensor terminals are rusty: then check through Navigator if the temperature indicated is

plausible in relation to the ambient temperature. Check also that the sensor electrical charac-

teristics are observed: replace the sensor if not OK; if it is OK, check the sensor connector and

the Marelli control unit connector

Lambda sensor

Function

In charge of telling the control unit whether the

mixture is lean or rich.

Operation / Operating principle

The Marelli injection control unit reads and inter-

prets a voltage generated by the difference in oxy-

gen content between the exhaust fumes and the

ambient. It does not require an external supply

source but, in order to work properly, it should

reach a high operating temperature: that is why

there is a heating circuit inside.

Level in electrical circuit diagram:

Oxygen sen-

sor

Location:

•

sensor: exhaust pipe

•

Connector: near the probe

Electrical characteristics:

Heater circuit: 12 -14

at 20 °C (68 °F)

Pin-out:

Stelvio 1200 NTX MY11

Electrical system

ELE SYS - 113

Содержание Stelvio 1200 MY11 2011


































































































































































































































































































































































































Результаты поиска

Содержание Stelvio 1200 MY11 2011

Отзывы:

Похожие инструкции для Stelvio 1200 MY11 2011

Бренды по названию

Популярные бренды

MOTO GUZZI Stelvio 1200 MY11 2011, Руководство по обслуживанию станции

Результаты поиска

Содержание Stelvio 1200 MY11 2011

Отзывы:

Похожие инструкции для Stelvio 1200 MY11 2011

Бренды по названию

Популярные бренды