MOTO GUZZI Stelvio 1200 MY11 2011 Скачать руководство пользователя страница 76

Страница: 76 / 385

•

4 Reused clamps

•

7 Cable grommets

•

5 Rubber clamps

•

7 Cable grommets

•

1 Adhesive cable grommet

•

1 Cable grommet with clip

Motorcycle division

The wiring timing is subdivided in three essential

sections, as indicated in the figure.

1. Front section

2. Central section

3. Rear section

Special checks for the correct connection and laying of cables

It is extremely important that any security-locks for the following connectors are properly connected and

correctly tightened to ensure proper engine, and therefore proper vehicle, operation.

•

Instrument panel connector

•

Pick Up connector and alternator

•

Side Stand Switch Connector

•

Coils connectors

•

Control unit connectors

•

Fuel pump connector

•

Key Connector

•

Right Light Switch Connectors

•

Left Light Switch Connectors

•

ABS connector and correct positioning of the cap

•

Front and rear speed sensor connector

•

Auxiliary Fuses (rubber housing correct positioning and closing)

•

Intake air temperature sensor

•

Fuel injector connectors

The connectors in the list are circled in the different pictures. The listed connectors are con-

sidered more critical than the others because their disconnection could cause the vehicle to

stop or malfunction. Obviously, the correct connection of the other connectors is also important

and essential for proper vehicle operation.

It is also important and essential that the instructions regarding the routing and fixing of the cable har-

ness in the various areas are followed meticulously in order to guarantee functionality and reliability.

Electrical system

Stelvio 1200 NTX MY11

ELE SYS - 76

Содержание Stelvio 1200 MY11 2011


































































































































































































































































































































































































Результаты поиска

Содержание Stelvio 1200 MY11 2011

Отзывы:

MOTO GUZZI Stelvio 1200 MY11 2011, Руководство по обслуживанию станции, Страница: 76 / 385

Результаты поиска

Содержание Stelvio 1200 MY11 2011

Отзывы: