MOTO GUZZI Stelvio 1200 MY11 2011 Скачать руководство пользователя страница 333 | Manualshive

Страница: 333 / 385

background image

light (5) on the instrument panel (4)

turns off.

CAUTION

IF THE ABS SWITCH IS PRESSED FOR MORE THAN TEN
SECONDS, THE SYSTEM DETECTS A FAILURE. TO ACTI-
VATE THE ABS SYSTEM AGAIN TURN THE IGNITION
SWITCH TO "OFF" AND THEN TO "ON".

IN CASE OF FAILURE OR WITH ABS DISCONNECTED,
THE VEHICLE OPERATES AS IF IT DID NOT HAVE THIS
SYSTEM.

20 A fuse (ABS Main fuse) (6)

Protects: ABS Control unit.

Guide to diagnosis

PREMISE

Each time the key is ON, if, at least one current or

stored* error is detected, the ABS warning light

turns on permanently.

The ABS system is deactivated!

The system operates perfectly just as any other

braking system without ABS

* The diagnosis requires exceeding the 5 km/h

(3.1 mph).

Each time the key is ON, if at least one current or stored* error of the ABS system is not detected:

•

the abs warning light flashes.

When the 5 km/h (3.1 mph) are exceeded:

- if errors are not detected: the ABS warning light turns off

- if at least one malfunction is detected: the ABS warning light turns on permanently.

The ABS system is disabled!

The system operates perfectly just as any other braking system without ABS.

The detection of malfunctions may require more or less time according to the type of failure.

Error detection logic foresees that for the errors to be diagnosed one or more conditions must persist

within a given time.

Stelvio 1200 NTX MY11

Braking system

BRAK SYS - 333

«
...
331
332
333
334
335
...
»

Содержание Stelvio 1200 MY11 2011


































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Stelvio 1200 MY11 2011

Бренд: Xenith Страницы: 17

Бренд: BMW Страницы: 176

GearTronic ZERO GT3100-K1

Бренд: PZRacing Страницы: 2

Бренд: kellermann Страницы: 2

Бренд: BMW Motorrad Страницы: 146

California EV V1100

Бренд: MOTO GUZZI Страницы: 173

Бренд: Yamaha Страницы: 86

Бренд: Yamaha Страницы: 86

Бренд: Yamaha Страницы: 86

Бренд: Yamaha Страницы: 100

Бренд: Yamaha Страницы: 88

Бренд: Yamaha Страницы: 119

MIO AL115S 2010

Бренд: Yamaha Страницы: 80

Бренд: Yamaha Страницы: 112

Бренд: Yamaha Страницы: 146

Бренд: Yamaha Страницы: 78

Бренд: Yamaha Страницы: 108

Бренд: Yamaha Страницы: 146

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды