MOTO GUZZI Stelvio 1200 MY11 2011 Скачать руководство пользователя страница 106

Страница: 106 / 385

Description of the defect:

the control unit detects an abnormal condition in the signals coming from

the speed sensors: for example, disturbances, signal intensity reduced, speed difference between the

two wheels for a certain period of time, etc.

Checks:

check the correct distance between speed sensor and tone wheel.

Solution:

restore the correct distance between speed sensor and tone wheel.

If functioning is correct, proceed to the next check

Checks:

check the tone wheel is not distorted (it should not be deformed or damaged).

Solution:

replace tone wheel

If functioning is correct, proceed to the next check

Checks:

check the speed sensor position and integrity.

Solution:

position the speed sensor correctly or replace it.

If functioning is correct, proceed to the next check.

Checks:

check tyres for wear (there should not be much difference between front and rear) and for

correct pressure.

Solution:

use tyres with the specified tyre wear condition and pressure.

If functioning is correct, proceed to the next check

Checks:

make sure that "the failure" has not been caused by using the vehicle in sport competitions.

Solution:

for example, avoid prolonged rearing up on the back wheel

Engine rpm sensor

Function

Informs crankshaft position and speed to the Mar-

elli control unit.

Operation / Operating principle

Inductive sensor: sinusoidal-type generated volt-

age; two teeth are missing on the flywheel for the

reference position.

Level in electrical circuit diagram:

Engine speed sensor

Location:

•

Sensor: Front left side of the engine,

under the generator.

•

Connector: Under the fuel tank.

Electrical characteristics:

•

Winding resistance 650 Ohm +/- 15%

•

Output alternating voltage, value

range: minimum: 0.5 V - maximum: 5 V

Electrical system

Stelvio 1200 NTX MY11

ELE SYS - 106

Содержание Stelvio 1200 MY11 2011


































































































































































































































































































































































































Результаты поиска

Содержание Stelvio 1200 MY11 2011

Отзывы:

Похожие инструкции для Stelvio 1200 MY11 2011

Бренды по названию

Популярные бренды

MOTO GUZZI Stelvio 1200 MY11 2011, Руководство по обслуживанию станции

Результаты поиска

Содержание Stelvio 1200 MY11 2011

Отзывы:

Похожие инструкции для Stelvio 1200 MY11 2011

Бренды по названию

Популярные бренды