MOTO GUZZI Stelvio 1200 MY11 2011 Скачать руководство пользователя страница 52

Страница: 52 / 385

Slot packing system

•

Fit both pistons on the connecting rods.

•

Working from both sides, fit the gasket

between the crankcase and the cylin-

der on the crankcase.

•

Fit both cylinders.

•

Take the left cylinder piston to TDC and

lock crankshaft rotation.

Specific tooling

020675Y

Service shaft gear lock

•

Thoroughly clean the upper surface of

both cylinders.

•

Place the tool on the left cylinder to de-

termine the "squish" (X).

•

Fasten the tool with the nuts of the stud

bolts.

Specific tooling

020676Y

Dial gauge support for piston position

checking

•

Reset the micrometer on the cylinder rim.

•

Move the tool so that the micrometer feeler reaches the top point of the piston crown.

•

Take note of the measurement and, according to the values found, consult the chart at the

bottom of the page to decide the thickness of the gasket to be fitted between cylinder and

head.

•

Unlock crankshaft rotation.

•

Rotate the crankshaft by 90°until the right cylinder piston reaches the TDC.

•

Lock crankshaft rotation.

•

Place the tool on the right cylinder stud bolts to determine the "squish" (X).

Specific tooling

020676Y

Dial gauge support for piston position checking

Characteristics

Stelvio 1200 NTX MY11

CHAR - 52

Содержание Stelvio 1200 MY11 2011


































































































































































































































































































































































































Результаты поиска

Содержание Stelvio 1200 MY11 2011

Отзывы:

MOTO GUZZI Stelvio 1200 MY11 2011, Руководство по обслуживанию станции, Страница: 52 / 385

Результаты поиска

Содержание Stelvio 1200 MY11 2011

Отзывы: